Abstract:Cu1.8S-based materials have become potential thermoelectric materials due to their rich raw material reserves, low toxicity, and excellent electrical and thermal properties. In this study, a series of Cu1.8–x Sbx S (x = 0, 0.005, 0.02, 0.03, 0.04) bulk materials is synthesized by using mechanical alloying combined with spark plasma sintering process. This preparation method can shorten the preparation cycle of materials, and effectively improve the research and development efficiency of thermoelectric (TE) materials due to its simple process. The effects of different Sb doping amounts on the structure, micromorphology, and thermoelectric transport properties of Cu1.8–x Sbx S phase are investigated. The results show that when 0 ≤ x < 0.02, the bulk samples are single-phase Cu1.8S. With the further increase of Sb doping to 0.02 ≤ x ≤ 0.04, the second phase CuSbS2 is formed when Sb content exceeds the solid solubility limit of x = 0.02 in Cu1.8S, all Cu1.8–x Sbx S bulk samples exhibit p-type conductivity characteristics. Benefitting from the synergistic phonon scattering effect by multiscale defects, such as point defects (\begin{document}${\rm{Sb}}_{{\rm{Cu}}}^{ \bullet\bullet }$\end{document}, \begin{document}$ {\rm{V}}_{\rm{S}}^{ \bullet \bullet } $\end{document}), nanopores, secondary phases (CuSbS2), and dislocations, the thermal conductivity κ declines significantly from 1.76 W·m–1·K–1 (x = 0) to 0.99 W·m–1·K–1 at 723 K for the Cu1.76Sb0.04S sample. Finally, the peak dimensionless TE figure of merit (ZT ) value of 0.37 is achieved at 723 K for Cu1.77Sb0.03S resulting from a low thermal conductivity of 1.11 W·m–1·K–1 combining an appropriate power factor of 563 μW·m–1·K–2, which is 12% higher than that (0.33) of pristine Cu1.8S. Although the Sb doped Cu1.8S-based samples have lower thermal conductivity κ, the reduced power factor cannot be offset by reducing the thermal conductivity κ, so the TE figure of merit (ZT ) value is not significantly improved. Therefore, there is still much room for improving the performance of Sb doped Cu1.8S-based thermoelectric material, and its thermoelectric performance can be further optimized through nano-second phase recombination, energy band engineering, and introducing multi-scale defects, etc. Our results suggest that the introduction of Sb into thermoelectric materials is an effective and convenient strategy to improve ZT value by reducing thermal conductivity κ.

Thermoelectric and Mechanical Properties of Nano BaTiO<sub>3</sub> Composited Cu<sub>1.8</sub>S Bulks

Nanostructured Bi2-Xcuxs3 Bulk Materials With Enhanced Thermoelectric Performance

Synergistic modulation of electrical and thermal properties of Cu<sub>1.8</sub>S bulk materials via nanostructuring and band engineering

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment

Enhancing Thermoelectric and Mechanical Performances in BiCuSeO by Increasing Bond Covalency and Nanostructuring

Enhanced performance of thermoelectric nanocomposites based on Cu12Sb4S13 tetrahedrite

Enhanced Thermoelectric and Mechanical Properties of p-type Bi0.5Sb1.5Te3 Bulk Alloys by Composite Electroless Plating with Ni&Cu

Enhanced thermoelectric performance of Bi0.3Sb1.7Te3 based alloys by dispersing TiC ceramic nanoparticles

Preparation and Thermoelectric Properties of Cu1.8S/CuSbS2 Composites

Effects of Electroless Plating with Cu Content on Thermoelectric and Mechanical Properties of p-type Bi0.5Sb1.5Te3 Bulk Alloys

Size Effect of SiO2on Enhancing Thermoelectric Properties of Cu1.8S

Enhanced thermoelectric properties of Cu1.8S via the introduction of ZnS nanostructures

Bi2Te3/Ti3C2T<inf>x</inf> Nanocomposites and Its Thermoelectric Properties Study

Phase structure and thermoelectric properties of Cu<sub>1.8-<i>x</i></sub>Sb<i><sub>x</sub></i>S thermoelectric material

Enhanced Thermoelectric Properties of Cu3SbSe4 Via Compositing with Nano-Snte

Enhanced thermoelectric and mechanical properties of Bi0.5Sb1.5Te3 alloy with dispersed yttrium oxide ceramic nanoparticles

Enhancing Thermoelectric Properties of (Cu2te)1−x-(Bicuteo)x Composites by Optimizing Carrier Concentration

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu 1.8 S via Carrier Concentration Regulation and Multiscale Phonon Scattering

Influence Mechanism of Nano-Tio2 Dispersion on Thermoelectric Properties of BiCuSeO

Bi2Te3/Ti3C2Tx Nanocomposites and Its Thermoelectric Properties Study

Phase Structure and Thermoelectric Properties of Cu<sub>1.8–<i>x</i></sub> Sb<i><sub>x</sub></i> S Thermoelectric Material