Abstract:AlN-SiC multiphase ceramics possess robust mechanical strength, high thermal conductivity and good oxidization resistance, and show great potential as the matrix material of fiber reinforced ceramic matrix composites. In this work, AlN-SiC multiphase ceramics were fabricated via low temperature reactive melt infiltration of Si-Al alloy into porous C-Si3N4 preforms. Influence of Si-Al source on the melt infiltration process was studied, and impact of residual silicon on the mechanical and thermal properties of the AlN-SiC ceramics was investigated. It was found that an Al-O layer was in- situ formed at the interface between Si-Al melt and C-Si3N4 preform, when Si-Al powder was used as the infiltration medium. This seriously retarded the melt infiltration process and made the penetration of Si- Al melt into the C-Si3N4 preform hardly possible. However, when Si-Al ingot was used as the infiltration medium, a well infiltration of Si-Al melt into the C-Si3N4 preform occurred, which led to the formation of dense AlN-SiC ceramics. Mechanical and thermal property measurements indicated that the strength of the AlN-SiC ceramics was significantly improved as the residual silicon content in it was reduced, while a reverse trend was observed for the thermal conductivity. AlN-SiC ceramics with 4%( in mass) residual silicon showed a high strength of 320.1 MPa, nearly comparable to that of conventional reaction bonded SiC, although its thermal conductivity was modest (26.3 W center dot m(-1)center dot K-1). The fundamental reasons for the above phenomena were discussed. This study is of great significance for the preparation of SiCf/AlN-SiC composites by low temperature reactive melt infiltration.

Study of Resistance Characteristics of Silicon Carbide Resistor Materials

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Microstructure, Porosity and Resistivity in Reaction-Bond ed Silicon Carbide

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Microstructure and Mechanical Properties of the Reaction-Sintered Silicon Carbide Ceramics Modified by Carbon Fiber

Study of SiC/Al nanocomposites under high pressure

Study on the Oxidation and Electrical Resistivity of Reaction-Bonded Silicon Carbide at High Temperature

Effect of Tungsten Carbide on Densification and Mechanical Properties of Silicon Nitride Ceramics by Spark Plasma Sintering

Preparation, microstructure and ion-irradiation damage behavior of Al4SiC4-added SiC ceramics

Fabrication and Characterization of ZrO_2/SiC Composite Materials

Effects of SiC Content on the Mechanical and Thermophysical Properties of 3D Cf/SiC–Al Composites

Microstructural, electrical, and mechanical properties of conductive SiC ceramics fabricated by spark plasma sintering

Effect of Different Aluminum Sources on the Preparation and Properties of SiC/Cordierite Composite Porous Ceramics

Improvement of Strength and Oxidation Resistance for SiC/graphite Composites by SiC Coating

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Pressureless Infiltration Preparation of High SiC/Al Ceramic Matrix Composites

Compressive Strength, Wear, and Structure Characteristics as a Result of Silicon Carbide Addition on a Copper Base

Fabrication and Properties of AlN-SiC Multiphase Ceramics <i>via</i> Low Temperature Reactive Melt Infiltration

Improving thermal conductivity of Al/SiC composites by post-oxidization of reaction-bonded silicon carbide preforms

Aqueous Processing, Hot-Pressing and Mechanical Properties of Silicon Carbide with Al2O3 and Y2O3

Study on the Performance for Silicon Carbide Ceramics by Hot-pressing Sintering