Abstract:Tensile response of a 2024Al alloy reinforced with Al2O3f/Al composite wires [(Al2O3f/Al)w/2024Al composite] has been investigated by both performing tensile tests and using the finite element method (FEM). Microstructure and tensile fracture surfaces of (Al2O3f/Al)w/2024Al composites were examined using optical microscope (OM) and scanning electron microscope (SEM), respectively. It is found that the longitudinal tensile response of (Al2O3f/Al)w/2024Al composite is nearly elastic up to failure. The longitudinal tensile strength of (Al2O3f/Al)w/2024Al composite reaches its fiber bundle strength and the longitudinal elastic modulus is consistent with that predicted using the rule of mixture. The contribution of matrix is negligible to the longitudinal tensile strength but not to the modulus of elasticity. Coating composite wires (CWs) with Ni can improve the interfacial bonding between the CWs and 2024Al alloy. Diffusion annealing can further improve the interfacial bonding. The transverse tensile strength is dependent strongly on the interfacial bonding between the CWs and 2024Al alloy. The stronger the interfacial bonding, the higher the transverse tensile strength. Following the diffusion annealing, ageing treatment can improve the transverse tensile strength of (Al2O3f/Al)w/2024Al composite to a higher level due to the increased strength of matrix 2024Al alloy. To reveal the fracture mode of (Al2O3f/Al)w/2024Al composite under transverse loading, the transverse tensile response of a model material, (Al2O3f/matrix1)w/matrix2 composite, whose microstructure is similar to that of the (Al2O3f/Al)w/2024Al composite, was analyzed using FEM. FEM results indicate that, under transverse loading, the stress distribution in the (Al2O3f/matrix1)w/matrix2 composite depends on the strength of matrix2. When matrix1 and matrix2 are both pure Al, failure initiates in matrix1. When matrix1 is pure Al and matrix2 is aged 2024Al alloy, however, failure initiates in matrix2 (2024Al). Therefore, for (Al2O3f/Al)w/2024Al composites with weak interfacial bonding between CWs and 2024Al matrix, cracks initiate at interfaces between the CWs and 2024Al matrix and propagate along the interfaces and then through 2024Al matrix, resulting in the global fracture. For (Al2O3f/Al)w/2024Al composite with strong interfacial bonding between CWs and 2024Al matrix, cracks initiate in either pure Al or 2024Al alloy and then propagate in both Al and 2024Al, resulting in the global fracture.

Preparation and Characterization of Aluminum Matrix Composites Based on Al–WO3 System

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

In situ (Al3Zrp+Al2O3np)/2024Al metal matrix composite with controlled reinforcement architecture fabricated by reaction hot pressing

Preparation and Characteristics of Al Matrix Composites Reinforced with ZnWO4 Coated (wo3p + ABOw) Hybrid Reinforcements

In situ fabrication and microstructure of Al2O3 particles reinforced aluminum matrix composites

Fabrication and Characteristics of in Situ Al12w Particles Reinforced Aluminum Matrix Composites by Reaction Sintering

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Preparation and characterization of Mo/Al 2 O 3 composites

Microstructure and Mechanical Properties of MoAlB Particles Reinforced Al Matrix Composites by Interface Modification with in Situ Formed Al12Mo

Preparation of MWNTs/Al2O3 Composites and Their Mechanical and Electrical Properties

Mechanical Properties of Al Matrix Composite Reinforced with Diamond Particles with W Coatings Prepared by the Magnetron Sputtering Method

Synthesis and characterization of an in-situ Al2O3/Al–Cu composite with a heterogeneous structure

Preparation and Mechanical Properties of in Situ Submicron MgAl2O4p/6061Al Composites from Al–Mg–SiO2 System

Fabrication and characteristic of Al-based hybrid composite reinforced with tungsten oxide particle and aluminum borate whisker by squeeze casting

Effect of surface modification of Al2O3 powder with Y2O3 on microstructure and tensile properties of aluninium matrix composites

High strength Al<SUB>2</SUB>O<SUB>3p</SUB>/6061 Al composites: effect of particles, subgrains and precipitates

Experimental and Simulation Investigations of Tensile Response of (al2o3f/al)w/2024al Composite

Fabrication and Characterization of Al2O3-WxSiy-WwBz Composite Prepared by Spark Plasma Sintering Method in Al-Si-WO3-B2O3 System

The properties and microstructure of hybrid composites reinforced with WO3 particles and Al18B4O33 whiskers by squeeze casting

In–situ synthesis of an Al composite reinforced with multi–scale Al12Mo, (Al, Zr, Si) and Al2O3 particles through a multi–stage reaction

Microstructures and mechanical properties of aluminum matrix composites fabricated from Al-x wt.% Zr(CO3)2 (x = 5, 10, 15, 20, 25) systems