Abstract:The electrodeposited Sn-Bi eutectic alloys can satisfy the need for micro-bumps with low melting point in 3D packaging. We deposited Sn-Bi film by pulse DC current in electroplating solutions based on methane sulfonic acid (MSA). The effects of MSA concentrations and pulse frequencies on morphology and composition of deposits were investigated. As the MSA concentration increased from 120 ml/L to 160 ml/L, the hydrogen evolution reaction weakened resulting in smoother deposited surfaces, and the Bi content decreased. In the use of pulses allowing deposits to become more uniform and denser, the Sn-56.73 wt% Bi film with smooth surfaces were fabricated at a pulse frequency of 4 Hz and an MSA concentration of 120 ml/L, of which melting point was 134.35 °C. By using transmission electron microscopy (TEM) and electron backscattered diffraction (EBSD), the structures were characterized more microscopically, which are essential for diffusion and electromigration of micro-bumps. The near-eutectic deposits, both before and after reflowing, consisted of uniformly distributed tetragonal β-Sn phases and hexagonal Bi phases, and the most preferred orientations after reflowing were the same as before reflowing, that were (220)//ND for β-Sn and ( 1̅ 012)//ND for Bi. The average grain sizes of Sn and Bi in the deposits after reflowing were 1.44 μm and 0.64 μm, respectively, which were much smaller than those of Sn58Bi alloy obtained by rapid solidification. Dislocations were observed in Sn grains and misorientation values in β-Sn phases were larger, which illustrated that the β-Sn phase carried larger strains. As evaluated by constant loading rate (CLR) nanoindentation tests, the hardness and modulus were significantly improved after reflowing, and creep stress indices of the deposits before and after reflowing were 51.74 and 7.07, respectively.

Fabrication of Bi-2212 Films on Ag Substrate by Dip-Coating Method

The Preparation and Characterization of Bi-2212 Film on Ag Substrate by Dip-Coating Method

Preparation of C-Axis Textured Bi-2212 Thin Films on Silver Substrates by Using Chemical Solution Deposition

Fabrication of Bi-2223 Superconducting Thick Films Via A Non-Vacuum Method on Silver Foil Substrates

Sputter deposition of bismuth and aluminum substituted dysprosium iron garnet films using sol-gel derived targets

Effect of Ag Doping on the Formation and Properties of Percolative Ag/BiFeO 3 Composite Thin Film by Sol–gel Method

PREPARATION OF Bi2Sr2Ca1Cu2Ox SUPERCONDUCTING FILMS ON Ag WIRES BY DIP-COATING METHOD

Preparation and electrical properties of ultra-thin Bi2212 films by sol-gel method

Fabrication of Bi-System High Temperature Superconducting Powder

Texture Development of Dip-Coated Bi-2223 Thick Films on Ag Substrate

A novel method to improve the morphology of Bi2212 film by PVA-assisted Pechini sol-gel method

Biaxially Textured (bi, Pb)(2)Sr2Ca2Cu3Ox Thin Films on LaAlO3 Substrates Fabricated Via the Chemical Solution Deposition Method

A New Approach of Preparing Nanocrystalline Bi-YIG Films

Fabrication of Ag-Bi Alloy Films from an Iodide-Tartrate Bath via Current Pulse Electrodeposition

Fabrication and properties of some Ag-alloy sheathed Bi-2223 tapes

Formation of Nano-Ag/Bifeo3 Composite Thin Film with Extraordinary High Dielectric and Effective Ferromagnetic Properties

Fabrication and characterization of Sn-57 wt% Bi film by pulse DC current co-electrodeposition and reflow

Enhancing Phase Purity of CSD Bi-2223 Thin Films Through Protected Sintering Method

A process for the preparation of high-quality and uniform large-scale Bi2212 superconducting films via the sol-gel method

Fabrication Of Ba0.6sr0.4tio3 Ceramic Thick Film By Electrophoretic Deposition Process

Fabrication of Ag injection in Bi2S3 (AgBiS2) thin films for photoelectrochemical cell applications