Abstract:The performance of superconducting magnets is greatly dependent on the size and uniformity of the superconducting filaments within the wire. However, in the fabrication of Bi 2 Sr 2 CaCu 2 O x (Bi2212) wires using ceramic oxide as the superconducting filaments, we face multiple challenges including filament fragility, poor uniformity, and non-smooth Ag/superconductor interfaces. These challenges primarily stem from the significantly lower plastic deformation capability of ceramic oxide powder filaments compared to metal matrices. To address these challenges, this study focuses on the modification of ceramic oxide precursor powders. Through the utilization of low-temperature, low oxygen partial pressure ( p O 2 ) heat treatment, we have observed significant changes in the Cu chemical states and lattice parameters within the Bi2212 grains. These alterations have proven to be highly effective in reducing the energy required for grain sliding and, in turn, enhancing the plastic deformation properties of the Bi2212 oxide filament. Furthermore, post-annealing the oxide powder under low p O 2 conditions narrows the gap in plastic deformability between the Ag sheath and the oxide filaments, resulting in improved filament uniformity and a smoother Ag/oxide interface in Bi2212 wires. Notably, the Bi2212 grains exhibit an orderly arrangement within the wires. As a result of these improvements, the critical current density ( J c ) of the final wires increases by an impressive 70 %. The outcomes of this study are not only crucial for producing Bi2212 magnets with higher magnetic field strength, improved magnetic field uniformity, and enhanced operational stability, but also offer fresh insights and methodologies for advancing the field of superconducting materials.

A novel method to improve the morphology of Bi2212 film by PVA-assisted Pechini sol-gel method

A process for the preparation of high-quality and uniform large-scale Bi2212 superconducting films via the sol-gel method

Preparation and electrical properties of ultra-thin Bi2212 films by sol-gel method

Optical Performance of PVDF/BCTH:0.005Sm 3+ Composite Film Via Hydrothermal Method and Scraping Process

Effects of Annealing Temperature on the Structures, Ferroelectric and Magnetic Properties of Aurivillius Bi5ti3feo15 Polycrystalline Films

Enhanced Superconductivity Induced by the Hexagonal-Array-Cooling-Shrinkage Effect

Fabrication of Bi-2223 Superconducting Thick Films Via A Non-Vacuum Method on Silver Foil Substrates

The intrinsic Josephson effect of Bi-2212 superconducting thin films prepared by sol-gel method

Effect of poly sodium-p-styrenesulfonate on the phase formation and morphology of the hydrothermally synthesized bismuth ferrite powders

A New Technique to Achieve Thick Tl2Ba2CaCu2O8 Films for Advanced Applications

Improvement of plastic deformation property and current carrying capacity of Bi2212 wires through low oxygen partial pressure post-annealing of precursor

Enhancing Phase Purity of CSD Bi-2223 Thin Films Through Protected Sintering Method

Phase purity and surface morphology of high-Jc superconducting Bi2Sr2Ca1Cu2O8+δ thin films

Nanoscale characterization of the doped SrZrO3 nanoparticles distribution and its influence on the microstructure of Bi2Sr2CaCu2O8+δ film

PREPARATION OF Bi2Sr2Ca1Cu2Ox SUPERCONDUCTING FILMS ON Ag WIRES BY DIP-COATING METHOD

Improving phase transformation and superconducting performance of Bi-2223 tapes via Cu addition

Preparation of C-Axis Textured Bi-2212 Thin Films on Silver Substrates by Using Chemical Solution Deposition

Fabrication of electrically bistable organic semiconducting/ferroelectric blend films by temperature controlled spin coating.

The evolution of Bi-2223 phase and liquid phase during the first heat treatment in Bi-2223/Ag superconducting tapes

Fabrication of organic PVP doping-based Ba 0.5Sr 0.5TiO 3 thick films on silicon substrates for MEMS applications

Facile Green Vacuum-Assisted Method for Polyaniline/SWCNT Hybrid Films with Enhanced Thermoelectric Performance by Interfacial Morphology Control