Abstract:The present work deals with the dilatometric study of a hot-rolled 0.2C3Mn1.5Si lean medium Mn steel, mainly suitable for the quenching and partitioning (Q&P) heat treatment in both hot-rolled or cold-rolled condition, subjected to a variation of austenitization temperature. These investigations were performed in a temperature range of 800–1200 °C. In this context, the martensite transformation start temperature (Ms) was determined as a function of austenitization temperature and in turn obtained prior austenite grain size (PAGS). The results show rise in prior austenite grain size due to increasing austenitization temperature, resulting in elevated Ms temperatures. Measured dilatation curves were confronted with the metallographic analysis by means of scanning electron microscopy (SEM). The present paper also focuses on the construction of a continuous cooling transformation (CCT) and deformation continuous cooling transformation (DCCT) diagram of the investigated lean medium Mn steel in a range of cooling rates from 100 to 0.01 °C/s and their subsequent comparison. By comparing these two diagrams, we observed an overall shift of the DCCT diagram to shorter times compared to the CCT diagram, which represents an earlier formation of phase transformations with respect to the individual cooling rates. Moreover, the determination of individual phase fractions in the CCT and DCCT mode revealed that the growth stage of ferrite and bainite is decelerated by deformation, especially for intermediate cooling rates. Microstructural changes corresponding to cooling were also observed using SEM to provide more detailed investigation of the structure and present phases identification as a function of cooling rate. Moreover, the volume fractions obtained from the saturation magnetization method (SMM) are compared with data from X-ray diffraction (XRD) measurements. The discussion of the data suggests that magnetization measurements lead to more reliable results and a more sensitive detection of the retained austenite than XRD measurements. In that regard, the volume fraction of retained austenite increased with a decrease of cooling rate as a result of larger volume fraction of ferrite and bainite. The hardness of the samples subjected to the deformation was slightly higher compared to non-deformed samples. The reason for this was an evident grain refinement after deformation.

CCT Diagram and Hardenability of 65mn Steel Produced by Compact Strip Production

The CSP Process Development of the Press Hardening Steel

Microstructure and Mechanical Properties of Hot-rolled 65mn Steel Produced by CSP

Mechanical Properties of Heat Treated 65mn Steel Produced by Compact Strip Production

Hot Ductility of High Carbon Steel Produced by Csp

Continuous cooling transformation dynamic CCT curve and microstructure of 65Mn steel

Practice on a High Carbon High Strength Steel Produced by Compact Strip Production

Analysis on continuous cooling transformation and microstructure control of 900 MPa grade high strength steel

Mechanical Properties of Heat Treated 30crmo Steel Produced by Compact Strip Production

Continuous Cooling Transformation Curves and Microstructures of Copper Bearing Low-Carbon Si-Mn Steel

Effect of Cooling Process on Microstructure and Mechanical Properties of Hot Rolled 65Mn Steel

Continuous Cooling Transformation and Structure Refinement of A Low Carbon High Strength Steel Produced by FTSR

Microstructure and mechanical properties of a hot-rolled 30CrMo steel produced by compact strip production

Continuous Cooling Phase Transformation Rule of 20crmnti Low-Carbon Alloy Steel

Cracking and segregation in high-alloy steel 0.4C1.5Mn2Cr0.35Mo1.5Ni produced by thick continuous casting

Effect of Finished Rolling Cooling Rate on Structure of Microalloy Non Quenched-Tempered Steel 34Mn2VN

Continuous Cooling Transformation of Overcooling Austenite and Structure Evolution of Si Steel

Optimizing Rolling Process Parameters of 65Mn Steel for Metallurgy Saw Blade by Thermal Simulation

Weldability of a 700MPa grade low carbon bainitic steel produced by CSP

Microstructure and Property of Laser Transformation Hardening on Sheet Steel with High Carbon Content

Austenite Decomposition of a Lean Medium Mn Steel Suitable for Quenching and Partitioning Process: Comparison of CCT and DCCT Diagram and Their Microstructural Changes