Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Effect of Cooling Process on Microstructure and Mechanical Properties of Hot Rolled 65Mn Steel

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Effect of Finished Rolling Cooling Rate on Structure of Microalloy Non Quenched-Tempered Steel 34Mn2VN

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Small Range Control of Pearlite Microstructure and Properties of 65Mn Hot Rolled Narrow Strip

Effects of Cooling Rate on Microstructure and Mechanical Properties of C-Si-Mn Dual-phase Steel As-hot-rolled

Effects of hot rolled microstructure after twin-roll casting on microstructure, texture and magnetic properties of low silicon non-oriented electrical steel

Upgrade Rolling Based on Ultra Fast Cooling Technology for C-Mn Steel

Effect of annealing temperature on microstructure and properties of 1100 MPa grade cold-rolled dual-phase steel

Effect of Rolling Temperature and Ultrafast Cooling Rate on Microstructure and Mechanical Properties of Steel Plate

Effect of Cooling Rate on Microstructure Evolution and Mechanical Properties of SCM435 Steel

Study on dynamic recrystallization of ultra-high strength 22MnB5 steel during hot rolling

The effect of the increased strain per pass during the hot-rolling and its effect on the tensile properties of V-Mo and Cr-V-Mo microalloyed dual-phase steels

Mechanism and control of nonuniform phase transformation of microalloyed dual-phase steel during cooling process after hot rolling

Microstructure evolution and compressive properties of a low carbon-low alloy steel processed by warm rolling and subsequent annealing

Effect of Cooling Practice on the Mechanical Properties of Medium‐Manganese Aluminum‐Alloyed Steels after Intercritical Annealing Quench and Partition Treatment

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Effect of Thermomechanical Controlled Processing on Microstructure and Cold Bending Properties of Automobile Beam Steel

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Influence of warm rolling temperature on multi-scale lamellar structure and mechanical properties of medium carbon steel

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys