Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Effect of Cooling Practice on the Mechanical Properties of Medium‐Manganese Aluminum‐Alloyed Steels after Intercritical Annealing Quench and Partition Treatment

Effect of Partition Temperature on Microstructure and Mechanical Properties of Cold‐Rolled Medium‐Manganese Steel

The impact of intercritical annealing temperature on microstructure and mechanical properties of an ultra-low carbon medium manganese heavy steel plates

Impact of Partitioning Temperature Parameters during the Quenching and Partitioning Process on Medium Carbon Steels with Two Different Alloying Strategies

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Effect of annealing time on microstructure and mechanical properties of Fe–C–Mn–Al–Si steel

Effect of Intercritical Annealing Time on Microstructure Evolution and Mechanical Properties of Low Carbon Medium Manganese Steel Subjected to Multi-Step Heat Treatment Process

Microstructure and Mechanical Properties of a Novel Cold Rolled Medium-Mn Steel with Superior Strength and Ductility

Effects of quenching and partitioning on microstructure and properties of high-silicon and high-aluminum medium carbon alloy steels

Effect of intercritical annealing temperature on microstructure and mechanical properties of V-Ti-Mo microalloyed medium Mn steel

Intercritically Annealed Medium-Manganese Steel: Insights into Microstructural and Microtextural Evolution, Strain Distribution, and Grain Boundary Characteristics

The influence of cooling methods on the austenite stability and plastic instability behavior in 3Mn steel

Tailoring retained austenite and mechanical property improvement in Al–Si–V containing medium Mn steel via direct intercritical rolling

Microstructure and Mechanical Properties of Hot-Rolled Medium-Mn Steel Containing 3% Aluminum

Optimizing Microstructure and Mechanical Properties of Cold-Rolled Medium-Mn Steel Through Intercritical Annealing and Warm Rolling

Microstructural Evolution of a Low-Carbon Steel during Application of Quenching and Partitioning Heat Treatments after Partial Austenitization

Effect of cooling rate on microstructure and mechanical properties of a low-carbon low-alloy steel

Influence of Intercritical Annealing on Microstructure, Ductility, and Toughness of Medium Mn Steels

Effect of precipitation-induced element partitioning during tempering on mechanical properties of hot-rolled 3Mn steel after intercritical annealing

Research on Hot Stamping-Carbon Partition-Intercritical Annealing Process of Medium Manganese Steel

Enhancing the ductility and yield strength of 2.7Mn steel via two-step partitioning heat treatment