Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Effect of intercritical annealing temperature on microstructure and mechanical properties of V-Ti-Mo microalloyed medium Mn steel

The impact of intercritical annealing temperature on microstructure and mechanical properties of an ultra-low carbon medium manganese heavy steel plates

Microstructural Evolution and Mechanical Properties of V-Containing Medium-Mn Steel Adopting Simple Intercritical Annealing

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Effect of C and Mn element partitioning behavior on microstructure and properties of cold-rolled medium manganese TRIP steel

Microstructure and Mechanical Properties of Hot-Rolled Medium-Mn Steel Containing 3% Aluminum

Effect of annealing time on microstructure and mechanical properties of Fe–C–Mn–Al–Si steel

Effect of annealing treatment on microstructure and mechanical properties of lightweight steels micro-alloyed with vanadium and niobium

Effect of Intercritical Annealing Time on Microstructure Evolution and Mechanical Properties of Low Carbon Medium Manganese Steel Subjected to Multi-Step Heat Treatment Process

Analysis of the Relationship Between Microstructure and Mechanical Properties of Intercritically Annealed 3.5mn Steel

Microstructure and mechanical properties of a novel medium Mn steel with Cr and Mo microalloying

Effect of Annealing Temperature and Time on Microstructure Evolution of 0·2c–5mn Steel During Intercritical Annealing Process

Influence of ε-martensite and austenite on mechanical properties by intercritical annealing in 0.1C-11Mn medium manganese steel

Influence of Intercritical Annealing on Microstructure, Ductility, and Toughness of Medium Mn Steels

Effects of annealing temperature and V addition on microstructure and mechanical properties of Fe-Mn-Al-C austenitic low-density steel

Influence of Thermo-Mechanical Process and Nb-V Microalloying on Microstructure and Mechanical Properties of Fe–Mn–Al–C Austenitic Steel

Effect of Low-Temperature Intercritical Annealing Time on Microstructure and Properties of 22mnb5 Steel

Characterization of Microstructures and Mechanical Properties of Cold-Rolled Medium-Mn Steels with Different Annealing Processes

Microstructural characteristics and tensile behavior of medium manganese steels with different manganese additions

The effect of Ti–Mo–Nb on the microstructures and tensile properties of a Fe–Mn–Al–C austenitic steel

Effect of Annealing Temperature on the Microstructure and Mechanical Properties of Selective Laser Melted Alloy Ti – 6% Al – 4% V