Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Optimizing Rolling Process Parameters of 65Mn Steel for Metallurgy Saw Blade by Thermal Simulation

Influence of Controlling Rolling and Cooling on Oxide Scale of 65Mn Steel for Metallurgy Saw Blade

Effect of Cooling Process on Microstructure and Mechanical Properties of Hot Rolled 65Mn Steel

Effect of Finished Rolling Cooling Rate on Structure of Microalloy Non Quenched-Tempered Steel 34Mn2VN

Design and Optimization of Heat Treatment Process Parameters for High-Molybdenum-Vanadium High-Speed Steel for Rolls

Effect of Cooling Rate on Pearlite Phase Transformation Behavior of 55Mn Steel

Effects of Controlled Rolling and Controlled Cooling on the Mechanical Properties of 550mpa Grade Engineering Mechanism Steel

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Investigation on Processing for a Titanium-Microalloyed Hot Rolled Dual Phase Steel

A Potential Hot Stamping Process for Microstructure Optimization of 22mnb5 Steels Characterized by Asymmetric Pre-Rolling and One- or Two-Step Pre-Heating

Analysis of Reasons for Straightening Fracture of 65Mn Steel Sheet after Spheroidizing Annealing in Metallurgical Saw Blade

Investigation on surface integrity and process parameter optimisation of carburised 18CrNiMo7-6 steel by induction-heating-assisted ultrasonic surface rolling process

Small Range Control of Pearlite Microstructure and Properties of 65Mn Hot Rolled Narrow Strip

Study on Thermal Deformation Behavior of 65Mn Steel for Saw Blade

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

The Influence of Hot Rolling Technological Parameters on Microstructure of Low Temperature Grain-Oriented Silicon Steel

Upgrade Rolling Based on Ultra Fast Cooling Technology for C-Mn Steel

Simultaneous enhancement of the strength and plasticity of Fe 12Mn steel by modulation of grain morphology

Effect of Process Parameters on Microstructural Evolution and Grain Refinement in a Low Carbon High Strength Microalloyed Dual Phase Steel

Study on dynamic recrystallization of ultra-high strength 22MnB5 steel during hot rolling

Parameters Optimization of Low Carbon Low Alloy Steel Annealing Process