Abstract:Severe plastic deformation (SPD) technologies are difficult to be promoted to be industrialized, and the processes are complicated, and the costs are high. To promote industrial application of the SPD technology for magnesium alloy, a new successive SPD method has been explored which includes direct extrusion and two steps equal channel angular extrusion (ECAE) continuously. The processing technology is called extrusion-shear (ES) in this paper. The components of ES dies have been designed, manufactured and installed on extruder to manufacture the AZ31 magnesium alloy rods. Microstructures of AZ31 magnesium alloy processed by ES process have been observed and investigated. The texture evolution during ES process has also been studied. The results show that fine and uniform microstructures can be obtained by ES process. Basal texture (0002) has been weakened owing to shear deformation of ES process. Research results show that relationship between grain sizes and hardnesses is consistent with hall-petch law at 420 degrees C. ES process with low billet temperature could improve hardness obviously and enhance compression performance, and raise strengths. And there exits strong tension-compression asymmetry of AZ31 magnesium alloy fabricated by ES process. The results indicate that ES process can produce large plastic deformation and introduce ultra-fined grains in the AZ31 magnesium alloy. (C) 2016 Elsevier B.V. All rights reserved.

Effects of Direct Extrusion Process on Microstructure, Texture Evolution and Yield Strength of Magnesium Alloy Az31

Influence of Extrusion Parameters on Grain Size and Texture Distributions of AZ31 Alloy

Effects of Dynamic Recrystallization in Extruded and Compressed Az31 Magnesium Alloy

Effect of grain size distribution and texture on the cold extrusion behavior and mechanical properties of AZ31 Mg alloy

Effects of Extrusion–Shear Process Conditions on the Microstructures and Mechanical Properties of AZ31 Magnesium Alloy

Influence of direct extrusion and torsional deformation on microstructure and properties of magnesium alloys

Effect of Hot Extrusion on Microstructure and Mechanical Properties of Electromagnetic Continuous Cast Az31 Magnesium Alloy

Effect Of Eche Forming On The Microstructure And Mechanical Properties Of Az31 Magnesium Alloy

Effect of Extrusion on Mechanical Properties of AZ91 Cast Magnesium Alloy

Effects of Temperature in the New Compound Extrusion on Microstructures and Properties of AZ61

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

Influences of Shear Angles on Microstructures and Compression Properties of AZ31 Mg Alloy Prepared by Extrusion-Shear Process

Effect of Extrusion Deformation on Microstructures and Properties of AZ31 Magnesium Alloy

Microstructure Evolution and Ductility Improvement Mechanisms of Magnesium Alloy in Interactive Alternating Forward Extrusion

Effect of Extrusion-Sheer on the Microstructure and Mechanical Properties of Magnesium Alloy AZ31

Effect of Extrusion Parameters on Microstructure and Mechanical Properties of Mg-7.5Gd-2.5Y-3.5Zn-0.9Ca-0.4Zr (wt%) Alloy

Effect of Extrusion Temperatures on Microstructures and Mechanical Properties of Mg-6Zn-1Mn-4Sn-0.5Y Alloy

Effects of the Extrusion Parameters on Microstructure, Texture and Room Temperature Mechanical Properties of Extruded Mg–2.49Nd–1.82Gd–0.2Zn–0.2Zr Alloy

Study of the microstructure, texture and tensile properties of as-extruded AZ91 magnesium alloy

The Influences of Extrusion-Shear Process on Microstructures Evolution and Mechanical Properties of AZ31 Magnesium Alloy

Evolution of Microstructure and Tensile Properties of Extruded Mg-4Zn-1Y Alloy