Abstract:In this study, ultra-fine grain Mg-3Zn-xCa-0.6Zr (x = 0, 0.6, 1.2, 1.8) alloy was obtained by a novel extrusion-shearing (ES) deformation process combining initial forward extrusion and subsequent equal channel angular extrusion (ECAP) shearing. The purpose of this paper is to improve the strength and plasticity of the alloy by ES process. The results of as-cast and homogenized alloy show that the ternary Ca2Mg6Zn3 phase with excellent thermal stability and refined grain size was formed in the alloy by adding Ca. In the ES process, the ternary phase was broken into ultra-fine particles pinned to the dynamic recrystallization (DRX) grain boundary, which introduced strong particle stimulated nucleation (PSN). Moreover, large number of MgZn phases in Ca-containing alloys were dynamically precipitated at DRX grain boundaries and within grains. In addition, in the early stage of the ES process, Ca2Mg6Zn3 phase promoted the accumulation of dislocations at the grain boundaries, and part of the grain boundary was transformed into low-angle grain boundaries (LAGBs) and high-angle grain boundaries (HAGBs). After the die corner shearing, the accumulated LAGBs gradually transformed into HAGBs due to continuous dynamic recrystallization (CDRX). Through the novel ES process and the addition of Ca element, the basal plane texture was significantly weakened and the DRX grain was refined. With the increase in Ca content, the strength and toughness of ES alloy increased obviously, and the yield asymmetry decreased gradually. When the content of Ca was 1.2 wt%, ES alloy exhibited the best combination of strength and toughness (UTS = 342 MPa, δ = 20.9%) due to nano-scale Ca2Mg6Zn3 phase, grain refinement and texture weakening. This property is of great significance for the development of magnesium alloys for biological applications.

Effects of Extrusion–Shear Process Conditions on the Microstructures and Mechanical Properties of AZ31 Magnesium Alloy

A special extrusion-shear manufacturing method for magnesium alloy rods based on finite element numerical simulation and experimental verification

Effects of Direct Extrusion Process on Microstructure, Texture Evolution and Yield Strength of Magnesium Alloy Az31

Investigation of microstructure and mechanical properties of ZK60 magnesium alloy achieved by extrusion-shearing process

Effects of Extrusion Processes on Microstructure and Properties of AZ31 Magnesium Alloy

Effect of Extrusion Deformation on Microstructures and Properties of AZ31 Magnesium Alloy

Effect of grain size distribution and texture on the cold extrusion behavior and mechanical properties of AZ31 Mg alloy

Microstructure and Mechanical Properties of Extruded Az31 Magnesium Alloy Sheet

Microstructure, Mechanical Properties, and Texture Evolution of Mg–Zn–Y–Zr Alloy Fabricated by Hot Extrusion–shearing Process

Microstructures and Corrosion Behavior of AZ61 Magnesium Alloy Prepared by Extrusion–Shear with Different Die Channel Angles

Numerical and Experimental Investigation on Hot Backward Extrusion Process of Mg-Gd-Y-Zn-Zr Magnesium Alloy

Influence of Extrusion Parameters on Grain Size and Texture Distributions of AZ31 Alloy

Microstructure and mechanical properties of Mg-Zn-Ca-Zr alloy fabricated by hot extrusion-shearing process

Unveiling the microstructure evolution and deformation mechanisms of micro-alloying Mg-1.5Zn-0.5Zr-0.5Sr alloy via extrusion-shearing

Fabrication of fine-grained, high strength and toughness Mg alloy by extrusion−shearing process

Thermomechanical Processing and Superplasticity of AZ91 Magnesium Alloy

Microstructure Evolution and Mechanical Properties of AZ31 Magnesium Alloy Sheets Prepared by Low-Speed Extrusion with Different Temperature

The Effects of Grain Size on Ductility of AZ31 Magnesium Alloy

Microstructure and Mechanical Properties of As-Cast and Hot Extruded–Sheared ZG61 Alloy

Microstructure Evolution and Hot Extrusion Behavior of AZ31-Nd Magnesium Alloy Adopting AZ31 Chips and Mg-Nd Chips

Effects of extrusion ratio and temperature on the microstructure and mechanical properties of Mg–Zn–Yb–Zr extrusion alloys