Abstract:Experiments were conducted to evaluate the effects of extrusion ratio on the microstructure and texture developments of AZ31 Mg alloy during forward extrusion. The forward extrusion was undertaken at 400°C with extrusion ratios of 10, 18, and 25 after the alloy was homogenized at 410°C for 12 h. Partially recrystallized microstructures were observed in all the extruded rods examined. The texture of the large elongated deformed grains appeared strongly centered at \(\left\langle {10\bar 10} \right\rangle\) dominating the extrusion texture, while the recrystallized grains exhibited much more randomized texture. For the alloy with the largest ER (25), coarse secondary recrystallized grains were found which presented a different texture component with \(\left\langle {11\bar 20} \right\rangle\) parallel to the ED. The occurrence of the coarse secondary recrystallized grains in the alloy with the largest ER might be attributed to that the large ER raised the die exit temperature during extrusion and thus promoted significantly grain growth after the extruded rod exited from extrusion die. The intensities of different texture components varied with ER because ER affected the contents of the deformed grains, DRX grains and coarse secondary recrystallized grains. In particular, the maximum intensity of fiber texture was decreased as ER increased due to the decrease of the large elongated deformed grains.

Influence of Extrusion Parameters on Grain Size and Texture Distributions of AZ31 Alloy

Effects of Direct Extrusion Process on Microstructure, Texture Evolution and Yield Strength of Magnesium Alloy Az31

Effect of grain size distribution and texture on the cold extrusion behavior and mechanical properties of AZ31 Mg alloy

Influence of Extrusion Ratio on Microstructure and Texture Developments of High-Temperature Extruded AZ31 Mg Alloy

Effects of Dynamic Recrystallization in Extruded and Compressed Az31 Magnesium Alloy

Influence of Extrusion Conditions on Microstructure and Mechanical Properties of Mg-2Gd-0.3Zr Magnesium Alloy

Effects of extrusion ratio on the microstructure and mechanical properties of AZ31 Mg alloy

Influence of direct extrusion and torsional deformation on microstructure and properties of magnesium alloys

Mechanical Properties Of Az31 Mg Alloy Extruded At Different Die Temperatures

Effects of the Extrusion Parameters on Microstructure, Texture and Room Temperature Mechanical Properties of Extruded Mg–2.49Nd–1.82Gd–0.2Zn–0.2Zr Alloy

The Effects of Grain Size on Ductility of AZ31 Magnesium Alloy

Texture and Its Effect on Mechanical Properties of AZ31 Magnesium Alloy

Effect of Extrusion Parameters on Microstructure and Mechanical Properties of Mg-7.5Gd-2.5Y-3.5Zn-0.9Ca-0.4Zr (wt%) Alloy

Effects of Extrusion Processes on Microstructure and Properties of AZ31 Magnesium Alloy

Study of the microstructure, texture and tensile properties of as-extruded AZ91 magnesium alloy

Effect of Extrusion on Mechanical Properties of AZ91 Cast Magnesium Alloy

Effect of Extrusion Deformation on Microstructures and Properties of AZ31 Magnesium Alloy

Mechanisms of Extrusion-Ratio Dependent Ultrafine-Grain Fabrication in AZ31 Magnesium Alloy by Continuous Squeeze Casting-Extrusion

Effects of the Extrusion Temperature on Microstructure, Texture Evolution and Mechanical Properties of Extruded Mg-2.49Nd-1.82Gd-0.19Zn-0.4Zr Alloy

Effects of extruding temperature on microstructure and mechanical properties of Mg-2.0Zn-0.3Zr-0.9Y alloy

Effect of extrusion parameters on microstructure and mechanical properties of Mg-0.12Ca-0.08Ba alloy