Abstract:TiAl-based alloy have potential as high temperature structural materials for aerospace applications, especially for thermal protection systems in aerospace vehicles including skin materials. Unfortunately, the ductility and formability of TiAl-based alloys are rather poor and thus gamma-TiAl sheets or foils are quite difficult to be manufactured by traditional methods and still far from practical applications. In the present work, commercial pure Ti foils and in-house fabricated TiB2/Al composite foils were alternately stacked and rolled to prepare Ti-(TiB2/Al) laminates, and then heat treatment was utilized to make liquid Al react with solid Ti, and finally TiAl-based composite sheet with multi-layer distributed reinforcement TiB2 particles were achieved. This method avoided the direct deformation of brittle TiAl billets and thus the near-net-shape processing of TiAl-based alloys sheets was feasible. Phase transformation and microstructure evolution during heat treatment were investigated and mechanical properties of the resulting micro-laminated TiB2-TiAl composite sheets were evaluated. The results showed that porous TiAl3 layers were produced by the reaction between liquid Al and solid Ti because of Kirkendall effect, and the following densification treatment under 50 MPa at 1300 degrees C for 2 h significantly improved the relative density of material. Subsequently, the reaction diffusion between TiAl3 and residual Ti proceeded in the following heat treatment, and finally fully lamellar (alpha(2)-Ti3Al+gamma-TiAl) layers were obtained. TiB2 particles did not participate in any reaction and remained, and displayed multi layered distribution in the matrix (alpha(2)-Ti3Al+gamma-TiAl) layers. TiB2 rich layer hindered the coarsening of lamellar colony of (alpha(2)-Ti3Al+gamma-TiAl) layer. Tensile properties at 800 degrees C of multi layered TiB2 TiAl composite sheets remarkably increased because of an increase of energy dissipation caused by plastic deformation.

Fabrication of Wavy Γ-Tial Based Sheet with Foil Metallurgy

Fabrication of Ti-Al-W-Si Alloy Sheet with Foil Metallurgy

Fabrication of Fully Dense Tial-Based Composite Sheets with A Novel Microlaminated Microstructure

PREPARATION AND PROPERTIES OF TiB2/TiAl COMPOSITE SHEETS WITH LAYERED STRUCTURE

Investigation on a Fabrication Technique of TiAl Sheet

Fabrication Of Multilayers Coatings Of Intermetallic Compound On Micro-Crystallization Ti-6al-4v Sheet By Al-Foil Pack Aluminizing

Macro-microscopic Morphology and Phase Analysis of TiAl-based Alloys Sheet Fabricated by EB-PVD Method

Preparation of γ-TiAl Alloy Based Sheet

Study on microstructure and properties of γ-TiAl/Ti-6Al-4V complex sheet

A High-Performance Β-Solidifying TiAl Alloy Sheet: Multi-type Lamellar Microstructure and Phase Transformation

Phase composition and microanalysis of TiAl-based alloys sheet by electron beam-physical vapor deposition

Research on microstructure of Ti-6Al-4V titanium alloy by thermal simulation under water cooling

Study of the Orientation Relationship of the Residual α2(Ti3Al) in γ(TiAl) Sheet After Heat Treatment

Dynamic Recrystallization of the Constituent Γ Phase and Mechanical Properties of Ti-43Al-9V-0.2Y Alloy Sheet

Microstructures and mechanical properties of hot-pack rolled Ti-43Al-9V-Y alloy sheet

Preparation of Gamma-Tial/Tc4 Composite Sheet and Its Microstructure and Properties

Processing and properties of gamma TiAl sheet from atomized powder

Study on Fabrication of Fine-Grained gamma-TiAl by Hot Isostatic Pressing Method and Its Formability

Study on Microstructure and Tensile Properties of New γ-TiAl Alloy Sheet

TiAl-BASED COMPOSITE SHEET WITH MULTI-LAYER DISTRIBUTED REINFORCEMENT PREPARED BY SOLID-LIQUID REACTION

Fabrication Of Tial Matrix Composite Sheetes With Controlled Micro-Laminated Architecture By A Solid-Liquid Reaction