Abstract:TiAl-based alloy have potential as high temperature structural materials for aerospace applications, especially for thermal protection systems in aerospace vehicles including skin materials. Unfortunately, the ductility and formability of TiAl-based alloys are rather poor and thus gamma-TiAl sheets or foils are quite difficult to be manufactured by traditional methods and still far from practical applications. In the present work, commercial pure Ti foils and in-house fabricated TiB2/Al composite foils were alternately stacked and rolled to prepare Ti-(TiB2/Al) laminates, and then heat treatment was utilized to make liquid Al react with solid Ti, and finally TiAl-based composite sheet with multi-layer distributed reinforcement TiB2 particles were achieved. This method avoided the direct deformation of brittle TiAl billets and thus the near-net-shape processing of TiAl-based alloys sheets was feasible. Phase transformation and microstructure evolution during heat treatment were investigated and mechanical properties of the resulting micro-laminated TiB2-TiAl composite sheets were evaluated. The results showed that porous TiAl3 layers were produced by the reaction between liquid Al and solid Ti because of Kirkendall effect, and the following densification treatment under 50 MPa at 1300 degrees C for 2 h significantly improved the relative density of material. Subsequently, the reaction diffusion between TiAl3 and residual Ti proceeded in the following heat treatment, and finally fully lamellar (alpha(2)-Ti3Al+gamma-TiAl) layers were obtained. TiB2 particles did not participate in any reaction and remained, and displayed multi layered distribution in the matrix (alpha(2)-Ti3Al+gamma-TiAl) layers. TiB2 rich layer hindered the coarsening of lamellar colony of (alpha(2)-Ti3Al+gamma-TiAl) layer. Tensile properties at 800 degrees C of multi layered TiB2 TiAl composite sheets remarkably increased because of an increase of energy dissipation caused by plastic deformation.

Preparation of Gamma-Tial/Tc4 Composite Sheet and Its Microstructure and Properties

PREPARATION AND PROPERTIES OF TiB2/TiAl COMPOSITE SHEETS WITH LAYERED STRUCTURE

Fabrication of Fully Dense Tial-Based Composite Sheets with A Novel Microlaminated Microstructure

Study on microstructure and properties of γ-TiAl/Ti-6Al-4V complex sheet

TiAl-BASED COMPOSITE SHEET WITH MULTI-LAYER DISTRIBUTED REINFORCEMENT PREPARED BY SOLID-LIQUID REACTION

Fabrication Of Tial Matrix Composite Sheetes With Controlled Micro-Laminated Architecture By A Solid-Liquid Reaction

Preparation of a Novel Layer-Structured Ti3Al Matrix Composite Sheet by Liquid–solid Reaction Between Al Foils and TiB/Ti Composite Foils

Interface Characteristics and Mechanical Properties of a Ti–TiAl Laminated Composite

Fracture Mechanism of a High Tensile Strength and Fracture Toughness Ti6Al4V–TiAl Laminated Composite

Enhanced tensile strength and fracture toughness of a Ti-TiAl metal-intermetallic laminate (MIL) composite

Preparation and Performance of Large-Sized Ti/Ti-Al Microlaminated Composite

A High-Performance Β-Solidifying TiAl Alloy Sheet: Multi-type Lamellar Microstructure and Phase Transformation

Processing and properties of gamma TiAl sheet from atomized powder

Study on Microstructures and Mechanical Properties of Ti/Ti-Al Microlaminated Composite

Fabrication, Microstructure Characterization and Fracture Behavior of a Unique Micro-Laminated TiB-TiAl Composites

Fabrication of (Tib/ti)-Tial Composites with a Controlled Laminated Architecture and Enhanced Mechanical Properties

Evolution of microstructural characteristic and tensile properties during preparation of TiB/Ti composite sheet

Preparation and characteristics of Ti3AlC2 -Al3Ti/Al composite materials synthesized from pure Al and Ti3AlC2 powders

Tailoring Ultrafine Grained and Dispersion-Strengthened Ti2AlC/TiAl Composite Via a New Fabrication Route

Synthesis and Mechanical Properties of Innovative (Tib/ti)-Ti3al Micro-Laminated Composites

Microstructure, Properties and Strengthening Mechanism of Cu-Tib2-Al2o3 Composite Prepared by Liquid Phase In-Situ Reaction Casting