Abstract:TiAl-based alloy have potential as high temperature structural materials for aerospace applications, especially for thermal protection systems in aerospace vehicles including skin materials. Unfortunately, the ductility and formability of TiAl-based alloys are rather poor and thus gamma-TiAl sheets or foils are quite difficult to be manufactured by traditional methods and still far from practical applications. In the present work, commercial pure Ti foils and in-house fabricated TiB2/Al composite foils were alternately stacked and rolled to prepare Ti-(TiB2/Al) laminates, and then heat treatment was utilized to make liquid Al react with solid Ti, and finally TiAl-based composite sheet with multi-layer distributed reinforcement TiB2 particles were achieved. This method avoided the direct deformation of brittle TiAl billets and thus the near-net-shape processing of TiAl-based alloys sheets was feasible. Phase transformation and microstructure evolution during heat treatment were investigated and mechanical properties of the resulting micro-laminated TiB2-TiAl composite sheets were evaluated. The results showed that porous TiAl3 layers were produced by the reaction between liquid Al and solid Ti because of Kirkendall effect, and the following densification treatment under 50 MPa at 1300 degrees C for 2 h significantly improved the relative density of material. Subsequently, the reaction diffusion between TiAl3 and residual Ti proceeded in the following heat treatment, and finally fully lamellar (alpha(2)-Ti3Al+gamma-TiAl) layers were obtained. TiB2 particles did not participate in any reaction and remained, and displayed multi layered distribution in the matrix (alpha(2)-Ti3Al+gamma-TiAl) layers. TiB2 rich layer hindered the coarsening of lamellar colony of (alpha(2)-Ti3Al+gamma-TiAl) layer. Tensile properties at 800 degrees C of multi layered TiB2 TiAl composite sheets remarkably increased because of an increase of energy dissipation caused by plastic deformation.

Investigation on a Fabrication Technique of TiAl Sheet

Growth Kinetics of TiAl3 Layer in Multi-Laminated Ti–(TiB2/Al) Composite Sheets During Annealing Treatment

Fabrication of Wavy Γ-Tial Based Sheet with Foil Metallurgy

Fabrication of Ti-Al-W-Si Alloy Sheet with Foil Metallurgy

A High-Performance Β-Solidifying TiAl Alloy Sheet: Multi-type Lamellar Microstructure and Phase Transformation

Reaction behaviors occurring in Ti/Al foil metallurgy

Fabrication Of Multilayers Coatings Of Intermetallic Compound On Micro-Crystallization Ti-6al-4v Sheet By Al-Foil Pack Aluminizing

TiAl-BASED COMPOSITE SHEET WITH MULTI-LAYER DISTRIBUTED REINFORCEMENT PREPARED BY SOLID-LIQUID REACTION

Study of the Orientation Relationship of the Residual α2(Ti3Al) in γ(TiAl) Sheet After Heat Treatment

Fabrication, Microstructure Characterization and Fracture Behavior of a Unique Micro-Laminated TiB-TiAl Composites

Fabrication and Processing of Gamma Titanium Aluminides - A Review

Recent Progress on the Fabrication of TiAl-Based Composites Sheet by Reaction Annealing of Elemental Foils

Fabrication Of Tial Matrix Composite Sheetes With Controlled Micro-Laminated Architecture By A Solid-Liquid Reaction

Application and microstructure control of TiAl intermetallics

Macro-microscopic Morphology and Phase Analysis of TiAl-based Alloys Sheet Fabricated by EB-PVD Method

Study on microstructure and properties of γ-TiAl/Ti-6Al-4V complex sheet

Fabrication of in situ Al3Ti/Al composites by using ultrasound assisted direct reaction between solid Ti powders and liquid Al

Tensile properties and fracture toughness of TiAl alloys with controlled microstructures

Processing of Ti-24 Al-14 Nb-3 V alloy foils

Preparation of γ-TiAl Alloy Based Sheet

Processing and properties of gamma TiAl sheet from atomized powder