Abstract:TiAl alloys are widely used in the aerospace industry and, hence, a thorough understanding of the corresponding microstructural evolution is crucial for providing insight into the fabrication of high-performance TiAI alloy sheets. In this study, a high-performance beta-solidifying Ti-43A1-9V-0.2Y alloy sheet with multi-type lamellar structures was obtained via hot-rolling at an initial rolling temperature of 1260 degrees C. Owing to the temperature drop and reheat associated with multi-pass rolling, relatively fine irregular beta/gamma and regular alpha(2)/gamma lamellar microstructures (average size: -25 mu m) with nano-scaled antiphase domains (APDs) were generated by the beta ->gamma and alpha + gamma -> alpha(2) + gamma/gamma(T) phase transformations. These two lamellar structures have different formation mechanisms. The results of electron backscatter diffraction and transmission electron microscopy revealed that the. nucleation and growth of (i) beta/gamma and (ii) alpha(2)/gamma lamellar structures are induced mainly by (i) stress and (ii) a combination of the stress and temperature drop during hot-rolling, respectively. Thin gamma(T) precipitates from the alpha/alpha(2) or gamma phases. This precipitation is induced by the higher stress and lower temperature associated with the later stage (compared with those occurring in the initial stages) of hot-rolling. Moreover, compared with the corresponding as-forged alloy, the as-rolled TiAl alloy sheet exhibits better performance at both room and elevated temperatures. The improvement in the tensile properties is attributed to the duplex microstructure consisting of fine multi-type lamellar structures with nano-scaled APDs. The interface boundaries of beta/gamma, alpha(2)/gamma and APDs, which are effective in retarding dislocation motion, contribute mainly to strengthening of the alloy sheet.

Study of the Orientation Relationship of the Residual α2(Ti3Al) in γ(TiAl) Sheet After Heat Treatment

Evolution of the microstructure of as-rolled Ti-43AI-9V-Y alloy with different heat treatments

Effect of Heat Treatment on the Microstructure and Mechanical Properties of TiAl Alloys

Study on Microstructure and Tensile Properties of New γ-TiAl Alloy Sheet

In-situ observation microstructure evolution and growth kinetics of lamellar γ phases in Ti44Al alloy during heat treatment

Microstructures and mechanical properties of hot-pack rolled Ti-43Al-9V-Y alloy sheet

Effect of Hot-Pressing Temperature on Microstructure and the Improvement of Residual Al on Tensile Ductility of Ti/Al3Ti Heterogeneous Structure

Investigation on a Fabrication Technique of TiAl Sheet

Dynamic Recrystallization of the Constituent Γ Phase and Mechanical Properties of Ti-43Al-9V-0.2Y Alloy Sheet

The Influences of Heat Treatment on the Microstructure and Mechanical Properties of Rolled Ti2AlNb

Study on microstructure and properties of γ-TiAl/Ti-6Al-4V complex sheet

Heat Treatment and Performance of PM-TiAl Base Alloy

Effect of Hot Rolling and Heat Treatment on Microstructure and Tensile Properties of High Strength Beta Titanium Alloy Sheets

Microstructure Evolution and Properties of Powder Metallurgy Ti43Al9V0.3Y Alloy Sheets at Different Rolling Temperatures

Effect of Heat Treatment on the Microstructure and Mechanical Properties of a Ti-TiAl Laminate Composite

Microstructure, Texture and Mechanical Properties of Ti-43Al-9V-0.2Y Alloy Hot-Rolled at Various Temperatures

A High-Performance Β-Solidifying TiAl Alloy Sheet: Multi-type Lamellar Microstructure and Phase Transformation

Effect of Heat Treatment on Microstructures and Mechanical Properties of a Novel Β-Solidifying TiAl Alloy

Fabrication of Wavy Γ-Tial Based Sheet with Foil Metallurgy

Evaporation of Al and microstructural variation in TiAl alloy during heat treatment

Effect of various heat treatment conditions on microstructures and mechanical properties of Ti-23Al-25Nb