Abstract:To improve the structure and hard elasticity of poly(vinylidene fluoride) (PVDF) fibers, a small amount of the plasticizer dibutyl phthalate (DBP) was added to PVDF. The PVDF/DBP blend fibers were prepared by melt spinning and subsequent annealing. The crystalline structure and thermal properties of the blend fibers were analyzed in terms of the long-period lamellar spacing, crystal structure, and degree of crystallinity with X-ray diffraction, differential scanning calorimetry, and small-angle X-ray scattering. The results indicated that stacked crystalline lamellae, which were aligned normal to the fiber axis, existed in the blend fibers, and they were in the form of an alpha-crystal phase. The total crystallinity of the blend fibers was higher than that of the pure PVDF fibers, and it reached its highest value when the DBP concentration was 2 wt %; then, it decreased with an increase in the DBP content. The morphology and mechanical properties of the fibers were also investigated with scanning electron microscopy and electronic tensile experimentation. The results of scanning electron microscopy apparently exhibited a small porous structure on the surface of the blend fibers, and the more DBP there was in the PVDF fibers, the more porous structure was obtained. Mechanical experiments indicated that the fibers with a 5 wt % concentration of DBP had better elastic recovery and breaking strain than the pure PVDF fibers. These results all indicated that DBP-modified PVDF fibers have potential applications in preparing microporous membranes by a melt spinning and stretching process. (C) 2009 Wiley Periodicals, Inc. J Appl Polym Sci 114: 3645-3651, 2009

Study on fracture of PVC/MBS blends

Plasticizer Effect of Dibutyl Phthalate on the Morphology and Mechanical Properties of Hard Elastic Poly(Vinylidene Fluoride) Fibers

Effect of Matrix Composition on the Fracture Behavior of Rubber-Modified Pmma/Pvc Blends

Variation of core-shell structural particles and their toughening behavior in poly (vinyl chloride) (PVC) matrix

Phase Separation of Impact‐modified PVC/PMMA Blends under Melt‐blending Conditions

Preparation and Properties of PMMA Blends with High Toughness

Synergistic toughening effect of SBS and HDPE on the fracture of the PS/HDPE/SBS blends

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Study on the property of PVC modified by MBS/inorganic material composite

EFFECT OF RUBBER AND INORGANIC RIGID PARTICLES ON FRACTURE BEHAVIOR OF INJECTION-MOLDED PVC NANOCOMPOSITES

Effect of PBT Resin on the Structure and Properties of Core-Shell Particles Toughened PC

The influence of the internal structure of core-shell particles on poly(vinyl chloride)/(methyl methacrylate-butadiene-styrene) blends

MODIFICATION OF PVC/PS BLEND WITH SOME DIFFERENT ELASTOMERS

Effect of Core-Shell Particles Dispersed Morphology on the Toughening Behavior of PBT/PC Blends

Toughening of Pbt/Pc Blends with Epoxy Functionalized Core-Shell Modifiers

Effect of Acrylate Toughening Agent on the Impact and Fusion Characteristics of PVC

Effect of Ethylene/butyl methacrylate/Glycidyl Methacrylate Terpolymer on toughness and biodegradation of poly (l-lactic acid)

Research on Toughening of Flame-retardant PBT/ABS Alloys

Necessity of Interfacial Interaction on Toughness Improvement for Ipp/msebs Blends

Experimental study on mechanical behaviors of injection molded PC/PMMA blends

Influence of Core-Shell Particles Structure on the Morphology and Brittle-Ductile Transition of Pbt/Abs-G-Gma Blends