Abstract:With increasing requirements for environmental protection and energy conservation, Al–Cu powder alloys play an important role in machine weight reduction. During the preparation of the Al–Cu powder alloy, an appropriate sintering temperature helps improve the comprehensive performance of the alloys. In this study, powder metallurgy was used to prepare Al–7.5Cu–1Si alloys, and the effects of different sintering temperatures on their relative sintering density, hardness, and tensile strength were studied. The microstructure and phase composition of the alloy were observed and analyzed by scanning electron microscopy and X-ray diffraction, and the mechanical properties of the alloy were studied using a Brinell hardness tester and a universal material testing machine. By analyzing the microstructural changes of the alloys at different sintering temperatures, the optimal sintering temperature of the alloy was determined to obtain the best properties. The results demonstrated that the sintering temperature significantly affected the diffusion and migration of the metal particles inside the alloy. When the temperature was low, numerous pores were present in the alloy, and the degree of bonding between the metal particles was poor. As the temperature increased, the number of pores in the alloy decreased, and good metallurgical bonding occurred between the particles. The relative densities and mechanical properties of the alloys were significantly affected by the sintering temperature. When the temperature was below 570 °C, the relative density and mechanical properties were low. At 590 °C, the alloy underwent deformation and was in an over-sintered state. The best sintering temperature was 570 °C. This is because at this temperature, the relative sintering density, hardness, and tensile strength of the alloy all reached maximum values, which were 98.6%, 71 HB, and 153 MPa, respectively.

Effect of sintering temperature on microstructure and properties of cemented carbide with iron and nickel-based bonders

Effect of sintering temperature on the microstructure and properties of Ti/W–C reinforced Fe-based composites

L1 2 strengthening of WC-CoNiFe cemented carbides by spark plasma sintering

The effect of binder phase content on WC-AlCoCrFeNiTi0.2 high entropy cemented carbides microstructure and mechanical properties

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Fabrication of WC-12Co cemented carbide by microwave sintering

Preparation and mechanical properties of SiCw-reinforced WC-10Ni3Al cemented carbide by microwave sintering

Effect of WC grain size on mechanical properties and microstructures of cemented carbide with medium entropy alloy Co-Ni-Fe binder

Effect of Particle Size and Vacuum Sintering Temperature on Phase Composition and Mechanical Properties of WC-12 Wt% Co Hardmetals

Effects of Ni content and sintering temperature on the microstructure and mechanical properties of TiC-Ni composites fabricated by selective carburization of Ti-Ni alloys

Preparation of WC-Co Cemented Carbide by Spark Plasma Sintering: Microstructure Evolution, Mechanical Properties and Densification Mechanism

Research on Microstructure and Properties of Ultrafine Grained WC-Ni3Al Cemented Carbide

Effect of Metal Elements on Microstructure and Mechanical Properties of Ultrafine Cemented Carbide Prepared by SPS

Influence of Temperature in Barothermal Treatment of Sintered Cemented Carbides on the Evolution of Their Structure and Properties

The Effect of Carbon Content on the Microstructure and Mechanical Properties of Cemented Carbides with a CoNiFeCr High Entropy Alloy Binder

Effect of carbon content on the microstructure and properties of Cr-doped WC–15Co cemented carbide

Tuning microstructure for superb mechanical properties in a Ti(C,N)-(WMoTaNbTi)C-Ni/Co cermets via change sintering temperature

Effect of sintering temperature on the microstructure and properties of Al-7.5Cu-1Si alloy