Abstract:Molybdenum disulfide shows promise as an anode material for lithium-ion batteries. However, its commercial potential has been constrained due to the poor conductivity and significant volume expansion during the charge/discharge cycles. To address these issues, in this study, N-doped MoS2/C composites (NMC) were prepared via an enhanced hydrothermal method, using ammonium molybdate and thiourea as molybdenum and sulfur sources, respectively. Polyethylene glycol 400 (PEG400) and polyvinylpyrrolidone (PVP) were added in the hydrothermal procedure as soft template surfactants and nitrogen/carbon sources. The crystal structure, morphology, elemental composition, and surface valence state of the N-doped MoS2/C composites were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), and X-ray photoelectron spectroscopy (XPS), respectively. The results indicate that the NMC prepared by this method are spherical particles with a nanoflower-like structure composed of MoS2 flakes, having an average particle size of about 500 nm. XPS analysis shows the existence of C and N elements in the samples as C-N, C-C, and pyrrolic N. As anodes for LIBs, the NMC without annealing deliver an initial discharge capacity of 548.2 mAh·g-1 at a current density of 500 mA·g-1. However, this capacity decays in the following cycles with a discharge capacity of 66.4 mAh·g-1 and a capacity retention rate of only 12% after 50 cycles. In contrast, the electrochemical properties of the counterparts are enhanced after annealing, which exhibits an initial discharge capacity of 575.9 mAh·g-1 and an ultimate discharge capacity of 669.2 mAh·g-1 after 70 cycles. The capacity retention rate decreases initially but later increases and elevated afterward to reach 116% at the 70th cycle, indicating an improvement in charge-discharge performance. The specimens after annealing have a smaller impedance, which indicates better charge transport and lithium-ion diffusion performance.

Poly(2,5-dimercapto-1,3,4-thiadiazole)/sulfonated Graphene Composite As Cathode Material for Rechargeable Lithium Batteries

Facile and Scalable Synthesis of Micro-Mesoporous Carbon/magnesium Oxide/sulfur Composite for Lithium-Sulfur Batteries

Synthesis and Electrochemical Performance of Polypyrrole-Coated Sulfur/Multi-Walled Carbon Nanotube Composite Cathode Materials for Lithium/Sulfur Batteries

Graphene-Wrapped Sulfur Particles as a Rechargeable Lithium-Sulfur-Battery Cathode Material with High Capacity and Cycling Stability

Poly(diallyldimethylammonium Chloride)-Assisted Synthesis of MoS2/graphene Composites with Enhanced Electrochemical Performances for Reversible Lithium Storage

In Situ Polymerization Synthesis of Ternary Sulfur/Polypyrrole/Graphene Nanosheet Cathode for Lithium/Sulfur Batteries

Sulfur Composite Cathode Materials for Rechargeable Lithium Batteries

3D Pomegranate-Like TiN@graphene Composites with Electrochemical Reaction Chambers As Sulfur Hosts for Ultralong-Life Lithium-Sulfur Batteries.

Titanium Tri- and Di-Sulfide Nanobelts/Graphene Composites for Rechargeable Lithium Battery Cathodes and Enhancement of Reversible Capacities

Hierarchically Porous Carbon/Dmct/Pedot-Pss Ternary Composite As A Cathode Material for Lithium-Ion Battery

Graphene-Li2S-Carbon Nanocomposite for Lithium-Sulfur Batteries

A MnO2/Graphene Oxide/Multi-Walled Carbon Nanotubes-Sulfur Composite with Dual-Efficient Polysulfide Adsorption for Improving Lithium-Sulfur Batteries

Sulfur Cathode Based on Layered Carbon Matrix for High-Performance Li–S Batteries

Single-Layer Mos2/Graphene Dispersed in Amorphous Carbon: Towards High Electrochemical Performances in Rechargeable Lithium Ion Batteries

Porous Silicon–graphene–carbon Composite As High Performance Anode Material for Lithium Ion Batteries

Mesoporous 3D titanium dioxide embed carbon nanofibers with superior polysulfide adsorption ability for high electrochemical performance Li-S batteries

Nanosulfur/polyaniline/graphene composites for high-performance lithium–sulfur batteries: One pot in-situ synthesis

PEG-PVP-Assisted Hydrothermal Synthesis and Electrochemical Performance of N-Doped MoS2/C Composites as Anode Material for Lithium-Ion Batteries

A MnO 2 /Graphene Oxide/Multi-Walled Carbon Nanotubes-Sulfur Composite with Dual-Efficient Polysulfide Adsorption for Improving Lithium-Sulfur Batteries.

Performance Enhancement Of A Graphene-Sulfur Composite As A Lithium-Sulfur Battery Electrode By Coating With An Ultrathin Al2o3 Film Via Atomic Layer Deposition

Polypyrrole-modified carbon nanotubes@manganese dioxide@sulfur composite for lithium–sulfur batteries