Abstract:The Bi 2 Sr 2 CaCu 2 O x (Bi-2212) precursor powder has been successfully synthesized using the spray pyrolysis method, and the powder has also been made into high critical current density Bi-2212/Ag-alloy wire with 666 filaments through the oxide-powder-in-tube (PIT) and the partial-melt processing (PMP). The advantage of low segregation was found in the spray pyrolysis precursor powder due to the gas-film-barrier high-temperature calcination for the micro-sized atomized solution droplets during the spray pyrolysis process. The droplets are instantly transformed into nearly nano-sized spherical oxide powder, and the liquid phase segregation could only appear inside each of these powder spheres during the process. And the elemental content and elemental distribution in each droplet are perfectly uniform, improving the homogeneity of the final oxide powder. In conventional precursor powders that have only undergone a solid phase sintering, the liquid phase flows between the powders, resulting in severe segregation. As the segregation phenomenon was almost avoided, the content of the Bi 2 Sr 2 CuO x (Bi-2201) phase and (Sr, Ca) x Cu y O z (alkaline earth cuprates, AEC) phase in the precursor powder decreased, leading to the enhancement of the Bi-2212 content in the precursor powder and the conductive characteristics of the wire. The superconducting critical transition temperature T c of the final wire is 90.53 K, and the Δ T c value is only 0.08 K. The wire has a small Δ T c value, further indicating the higher purity of the superconducting sample. The critical current density ( J c ) of the Bi-2212 wire reaches 283 A/mm 2 at 65 K in self-field, which is higher than that of the wire reported in the literature. After high-pressure heat treatment, the highest J e and the highest J c of the wires reach 538 A/mm 2 and 2987 A/mm 2 at 4.2 K & 12T. It indicated that the spray pyrolysis method would be a candidate method for preparing high-performance Bi-2212 wire.

The Properties of Bi-2223 Precursor Powders Ground by Fluid Energy Comminuting

Preparation of Bi-Based Superconductor Precursor Powder by a Spray- Dry+ Fluidized Bed Denitration Technology

Synthesis of (Bi,Pb)-2223 superconductor powder by pechini method

The Effect of Wet Ball Milling in the Production Process of YBaCu Composite Oxide on its Superconducting Properties

EFFECT OF GRINDING ON Y-123 and Bi(Pb)-2223 PHASE SUPERCONDUCTORS

Optimization of a New Modified Wet-Chemistry Process for the Synthesis of BPSCCO Superconductor Precursor Powders with Specific Stoichiometr

Preparation of Nb3al by High-Energy Ball Milling and Superconductivity

Preparation of Nb 3 Al Superconductor by Powder Metallurgy and Effect of Mechanical Alloying on the Phase Formation

Synthesis and Characterizations of Nanocrystalline Wc-Co Composite Powders by A Unique Ball Milling Process

Performance Evaluation Of(bi,pb)2sr2ca2cu3ox Superconducting Precursor Powder by Analysis of Oxygen Partial Pressure

The influences of powder processing variables on the properties of Bi-2223/Ag tapes

Microstructure and Properties of W/Sm2O3 Composites Prepared Spark Plasma Sintering

Preparation of Ultrafine Powder of the Ba-Y-Cu-O System and Its Superconductivity

Improved Superconducting Properties in Bulk MgB2 Prepared by High Energy Milling of Mg and B Powder

Mechanical properties and microstructural evolution of pressureless sintered ceramics obtained from high-energy ball-milled TiB2–TiC powders

Preparation and Performance Study of SiC-Reinforced Fe-Based Wear-Resistant Composite Grinding Media

Preparation and properties of lead-free FeS/Cu-Bi composites by flake powder metallurgy via shift-speed ball milling

Preparation of high-performance high temperature superconducting Bi-2212 wires by the spray pyrolysis powder

Preparation and Superconductivity of Bi3PbCa3Sr3Cu4Oy

Enhancing the physical properties of Mo-Cu composites through plasma spheroidized spherical molybdenum powder

Fabrication of Bi-System High Temperature Superconducting Powder