Abstract:The Bi 2 Sr 2 CaCu 2 O x (Bi-2212) precursor powder has been successfully synthesized using the spray pyrolysis method, and the powder has also been made into high critical current density Bi-2212/Ag-alloy wire with 666 filaments through the oxide-powder-in-tube (PIT) and the partial-melt processing (PMP). The advantage of low segregation was found in the spray pyrolysis precursor powder due to the gas-film-barrier high-temperature calcination for the micro-sized atomized solution droplets during the spray pyrolysis process. The droplets are instantly transformed into nearly nano-sized spherical oxide powder, and the liquid phase segregation could only appear inside each of these powder spheres during the process. And the elemental content and elemental distribution in each droplet are perfectly uniform, improving the homogeneity of the final oxide powder. In conventional precursor powders that have only undergone a solid phase sintering, the liquid phase flows between the powders, resulting in severe segregation. As the segregation phenomenon was almost avoided, the content of the Bi 2 Sr 2 CuO x (Bi-2201) phase and (Sr, Ca) x Cu y O z (alkaline earth cuprates, AEC) phase in the precursor powder decreased, leading to the enhancement of the Bi-2212 content in the precursor powder and the conductive characteristics of the wire. The superconducting critical transition temperature T c of the final wire is 90.53 K, and the Δ T c value is only 0.08 K. The wire has a small Δ T c value, further indicating the higher purity of the superconducting sample. The critical current density ( J c ) of the Bi-2212 wire reaches 283 A/mm 2 at 65 K in self-field, which is higher than that of the wire reported in the literature. After high-pressure heat treatment, the highest J e and the highest J c of the wires reach 538 A/mm 2 and 2987 A/mm 2 at 4.2 K & 12T. It indicated that the spray pyrolysis method would be a candidate method for preparing high-performance Bi-2212 wire.

Preparation of Bi-Based Superconductor Precursor Powder by a Spray- Dry+ Fluidized Bed Denitration Technology

Preparation of Nb 3 Al Superconductor by Powder Metallurgy and Effect of Mechanical Alloying on the Phase Formation

The reaction process of the Bi-Sr-Ca-Cu-O system and the forming mechanism of the 2212 superconducting phase

Preparation of high-performance high temperature superconducting Bi-2212 wires by the spray pyrolysis powder

Optimization of a New Modified Wet-Chemistry Process for the Synthesis of BPSCCO Superconductor Precursor Powders with Specific Stoichiometr

Synthesis of (Bi,Pb)-2223 superconductor powder by pechini method

PREPARATION OF NANOSIZED Bi3.25 La0.75 Ti3 O12 POWDER BY COPRECIPITATION METHOD

Preparation of Nb3al by High-Energy Ball Milling and Superconductivity

Study on Phase-Formation Mechanism and Intergrowth for Bi(Pb)-Sr-Ca-Cu-O System

Preparation and Superconductivity of Bi3PbCa3Sr3Cu4Oy

STUDY ON THE FORMATION OF SUPERCONDUCTING PHASE IN Bi-BASED SUPERCONDUCTOR BY THE CHEMICAL KINETICS

Preparation And Phase Research Of The 110-K High-Tc Superconductor Bi2sr2ca2cu3oy Doped With Sb And Pb

Formation Mechanism of the 3321 Phase in Bi-System High Temperature Superconduting Materials

Preparation of 110k Superconductor in Bi-Sr-Ca-Cu-O System

Effects of Heat Treatment Temperature on Phase Formation and Properties of Bi-2212 Spray Pyrolysis Powder

The Properties of Bi-2223 Precursor Powders Ground by Fluid Energy Comminuting

Yba2cu3o7-Delta Superconductor Bulks Composited By Y2bacuo5 Nanoparticles Derived From Homogeneous Nucleation Catastrophe

Calcination and Phase Composition of BSCCO High Temperature Superconducting Powder

Preparation of Ultrafine Powder of the Ba-Y-Cu-O System and Its Superconductivity

Study On Bi(Pb, Sb)Srcacuo Superconductors Prepared By The Oxalate Coprecipitation Technique

A process for the preparation of high-quality and uniform large-scale Bi2212 superconducting films via the sol-gel method