Abstract:Fe-10%Ni alloys were synthesized in a high energy horizontal rotary ball mill from pure element Fe and Ni powders. Phase constitution, shape and thermal stability of the milled powders were characterized using X-ray diffractometry (XRD), scanning electron microscopy (SEM) and differential thermal analysis (DTA), respectively. And microstructure and properties of bulks prepared by hot-press sintering with milled powders as starting materials were analyzed and tested. Results indicate that under the condition of a milling speed of 400 r/min and a ball-to-powder mass ratio of 20:1, Ni fully solubilizes in Fe, which forms a supersaturate solid solution of Fe(Ni) with a body-centered cubic structure. Particles of the powder milled up to 16 h are more homogeneous and finer than those of the powder milled for 8 h, but phase of the powder is still Fe(Ni) solid solution. The alloy powder milled for 16 h were annealed in the temperature range between 500 and 800 degrees C. It is found that structure of the powder after annealing is stable and no phase transformation occurs in the powder. Phase of the powder is still Fe(Ni) solid solution. When the alloy powders milled for 16 h were treated by hot pressed sintering at 950 degrees C, a little Fe(Ni) solid solution with a face-centered cubic structure is found in the bulks. If the bulks that previously were treated by hot-press sintering at 950 degrees C and cooled to room temperature were subsequently sintered at 970 degrees C again, the phase of the powders completely transforms to Fe(Ni) solid solution with a face-centered cubic structure. However, the strength and ductility of bulks treated by hot-press sintering at 950 degrees C are superior to those of bulks by subsequent sintering at 970 degrees C, because oxide and holes are produced in resintered bulks without pressure.

Synthesis of NiAl(Cr,Nb) Powder by Mechanical Alloying

Preparation of ti-al based nanophase composite powder by mechanical alloying

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Preparation of Nb 3 Al Superconductor by Powder Metallurgy and Effect of Mechanical Alloying on the Phase Formation

Preparation of Cbnp/Nicral Nanostructured Composite Powders by A Step-Fashion Mechanical Alloying Process

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Microstructure and formation mechanism of Ni-Al intermetallic compounds fabricated by reaction synthesis

Nanocrystalline Ni-30wt%Fe Supersaturated Solid Solution Synthesized by Mechanical Alloying

SYNTHESIS OF NANOSTRUCTURED GAMMA-TiAl BASED POWDERS AND BULK ALLOYS USING HIGH ENERGY MECHANICAL MILLING AND HIP

The Morphology and Microstructure of Nanocrystalline Fe1-x-Nix Alloy Powders by Mechanical Alloying

Mechanical Alloying and Spark Plasma Sintering of Ni-Al-Ti-B Powders for Fabricating Nanocrystailine (Tib+tib2)/ni-3(Al, Ti) Composite

Formation of NiAl Intermetallic Compound by Cold Spraying of Ball-Milled Ni/Al Alloy Powder Through Postannealing Treatment

Study on preparation and mechanical property of nanocrystalline NiAl intermetallic

Fabrication Of Nanostructural Aluminum Alloy Powder With Ball Milling Method

Synthesized by Ball Milling Al-Pb-Si-Sn-Cu Nanocrystalline Powder

Research on Fe-10%Ni Alloy Synthesized by Mechanical Alloying

Deposition of NiAl/Al3Ni2(CrB2) Coatings from Ni, Al and CrB2 Powders Using Mechanical Synthesis in Planetary Ball Mill

Synthesis of Ultrafine Fe-W-Al-Ti-Ni-C-B Powders by Mechanical Alloying

Research of nanocrystalline Ni-30%Fe solid solution synthesized by mechanical milling

Microstructural evolution and thermal stability in a nanocrystalline lightweight TiAlV0.5CrMo refractory high-entropy alloy synthesized by mechanical alloying

Study on synthesis and structure of mechanically alloyed W-Ni-Fe nanocomposite powders