Abstract:In this work, single-phase Te-doped CoSb 3 polycrystalline bulk (Indium powder) and nanocomposites (α-WC nanopowder) were synthesized via a ball milling, hand-grinding and consolidated by spark plasma sintering technique. The thermoelectric and mechanical characteristics of as-synthesized composites were studied. The electrical resistivity varies between 11.82 and 12.82 μΩ-m for CoSb 2.875 Te 0.125 + x ( x = 0.33% In, 1% In, 2% In, 4% In and 1% In + 0.33% α-WC, respectively) composites. At temperature of 300 K, composite with x = 1% In exhibit the lowest resistivity of 11.82 μΩ-m. Also, negative values of Seebeck coefficients confirm that electrons are the predominant charge carriers. The maximum power factor of 2566 and 2482 μWm −1 K −2 are observed from x = 1% In and x = 1% In + 0.33% α-WC composites at 673 K, respectively. Notably, the power factor of 1% In and 1% In + 0.33% α-WC composites is slightly higher (1.05 times) than the CoSb 2.875 Te 0.125 sample. The composites with lowest weight percent of 1% In and 1% In + 0.33% α-WC have a considerably improved power factor. For the composite with x = 1% In + 0.33% α-WC, the minimum thermal conductivity of 2.32 W/m–K at 300 K was achieved through a combination of doping and dispersion in the CoSb 2.875 Te 0.125 matrix. It is possible that the multi-scale size distributions of grains will reduce the lattice thermal conductivity by scattering phonons over a large wavelength range. As a result, an increased figure of merit of 0.82 was achieved for CoSb 2.875 Te 0.125 + 1% In + 0.33% α-WC composites at 823 K. The results suggest that the doping with composite approach could boost thermoelectric efficiency in n-type CoSb 3 -based materials.

Microstructure and Thermoelectric Properties of CoSb3 Synthesized by MA-SPS Method

Thermoelectric Property of Fine-Grained CoSb3skutterudite Compound Fabricated by Mechanical Alloying and Spark Plasma Sintering

Mechanical Alloying Synthesis and Spark Plasma Sintering of CoSb3

Effects of Co:Sb Molar Ratio on Synthesis and Properties of Undoped Cosb3 Prepared Via A Polyol Method

Enhanced power factor and suppressed lattice thermal conductivity of CoSb3 Skutterudite by Ni substitution and nanostructuring for high thermoelectric performance

Effects of mechanical alloying process on thermoelectric properties of Bi2S3 Bulk

Enhancing Thermoelectric Properties of Polycrystalline Bi 2 S 3 by Optimizing a Ball-Milling Process

Influence of synthesis method and processing on the thermoelectric properties of CoSb3 skutterudites

Possible reduction of lattice thermal conductivity in n-type CoSb2.875Te0.125 skutterudite originating from collaborative adjustment between Indium micro and α-WC nano inclusions

Nanostructuring and Thermoelectric Properties of Bulk Skutterudite Compound Cosb3

Modification of the thermoelectric performance in Se alloyed CoSb1-xSexS

Metallization and Diffusion Bonding of CoSb3-Based Thermoelectric Materials

Dual occupations of sulfur induced band flattening and chemical bond softening in p-type S Co4Sb12-2S2 skutterudites

Significant enhancement of electrical conductivity by incorporating carbon fiber into CoSb3 thermoelectric skutterudite fabricated by spark plasma sintering method

Effect of Y-filling on Thermoelectric Properties of CoSb3

Thermoelectric Properties of Bi2Te3 Alloy Prepared by Mechanical Alloying and Spark Plasma Sintering

Nanostructured Bi2-Xcuxs3 Bulk Materials With Enhanced Thermoelectric Performance

New synthesis route of highly porous InxCo4Sb12 with strongly reduced thermal conductivity

Solvothermal synthesis of nanosized CoSb 3 skutterudite

Enhanced Thermoelectric Properties of Co 1− X − Y Ni X + Y Sb 3− X Sn X Materials

Enhanced thermoelectric properties of bismuth sulfide polycrystals prepared by mechanical alloying and spark plasma sintering