Abstract:Vortex pumps have good non-clogging performance and are widely used in the fluid transportation of food, sewage treatment, and mineral and coal slurry transportation. In order to design and manufacture a vortex pump with good performance and establish a method of optimum design, we must master the internal flow rules of the pump. Based on the self-design vortex pump (32WB8-12) experiment, the discharge-pump head (qv-H), discharge-pump shaft power (qv-P), discharge-pump efficiency (qv-η), and discharge-critical net positive suction head (qv-NPSHc) curves are obtained, and the qv-NPSHc curve shows an opposite tendency compared with the centrifugal pump. With the mathematical model selected with respect to the optimal condition, the three-dimensional internal flow within the vortex pump has been numerically simulated by a renormalization group k-ε (RNG k-ε) turbulence model. The static pressure (ps) and velocity distribution of the impeller and the middle section of the volute at 0°, 90°, 180°, and 270° are obtained, and the performance curves have been fitted using a CFX-calculated energy parameter. It was illustrated that the velocity field is relatively disordered and the flow in the impeller region is of a forced vortex character. The flow in the volute is similar to that of the combined vortex with backflow, which is a non-axisymmetric unsteady flow with quite high turbulence intensity. These factors are the main reasons for the relatively low efficiency of the vortex pump. The measurement of flow field in volute with a five-hole probe was conducted, and it is demonstrated that the numerical results are in good agreement with the flow field measurement data. An upward pressure gradient forms in the portal area of the impeller, and it is confirmed that the lowest pressure point is located in the upper position of the impeller hub. It is revealed that for the vortex pump to have advanced suction and anti-cavitation performance, the lowest pressure in the pump should be −4 × 104 Pa and it should be located at the center of the vortex chamber cavity.

Research on Diameter Parameter of Reverse Circulation Drilling Bit Based on CFD

Analysis of flow characteristics in the volute casing of centrifugal pump based on numerical simulation

Optimum Design of Large-Diameter Reverse Circulation Drill Bit for Drilling Rescue Wells Using Orthogonal Experimental Method and CFD Simulation

Experimental and Numerical Study on Air Flow Behavior for a Novel Retractable Reverse Circulation Drill Bit of Casing-while-Drilling (CwD)

Numerical investigation of geometry parameters on side-ejector DTH hammer RC bit

Simulation and Analysis of a Split Drill Bit for Pneumatic DTH Hammer Percussive Rotary Drilling

Experimental investigation and CFD simulation of multiphase flow behavior in air reverse circulation drilling

Numerical Simulation on Internal Flow in the Screw Centrifugal Pulp Pump

Investigation on the cuttings carrying capacity of a novel retractable drill bit used in casing while drilling with air reverse circulation

Insight into dust control performance of a reverse circulation drill bit using multiphase flow simulation

Lost Circulation Control for Pump-Injected Reverse Circulation Drilling: Experimental Optimization and Theoretical Analyses

Numerical Simulation and Analysis on Hydraulic Performance in Vertical Canned Motor Pump

Analytical and Numerical Simulation of Asymmetric Converging Flow of Gas Under Drill Bits in Reverse Circulation Gas Drilling

A Performance Test and Internal Flow Field Simulation of a Vortex Pump

Research on Cavitation Characteristic of Inducer

Numerical investigation of flow patterns in cuttings transport for extended-reach horizontal wells with rotation drillpipe

Design of Diamond Bits Water Passage System and Simulation of Bottom Hole Fluid Are Applied to Seafloor Drill

CFD-DEM Simulation of Reverse Circulation Pneumatic Cuttings Removal during Coal Seam Drilling

Experimental And Numerical Investigation Of The Flow Field In The Radial Inlet Of A Centrifugal Compressor

Numerical investigation into the abrasive particle movement characteristics inside the swirling impeller nozzle based on the coupled SPH-FEM method

Numerical Simulation of Effective Hole Cleaning by Using an Innovative Elliptical Drillpipe in Horizontal Wellbore