Abstract:The backreaming operation plays a significant role in safe drilling for horizontal wellbores, while it may cause severe stuck pipe accidents. To lower the risk of the stuck pipe in backreaming operations, the mechanism of cuttings transport needs to be carefully investigated. In this research, a transient cuttings transport with multiple flow patterns model is developed to predict the evolution of cuttings transported in the annulus while backreaming. The established model can provide predictions of the distribution of cuttings bed along the wellbore considering the bulldozer effect caused by large-size drilling tools (LSDTs). The sensitivity analyses of the size of LSDTs, and backreaming operating parameters are conducted in Section 4. And a new theory is proposed to explain the mechanism of cuttings transport in the backreaming operation, in which both the bit and LSDTs have the “cleaning effect” and “plugging effect”. The results demonstrate that the cuttings bed in annuli is in a state of dynamic equilibrium, but the overall trend and the distribution pattern are obvious. First, larger diameters and longer drilling tools could lead to a higher risk of the stuck pipe. Second, we find that it is not the case that the higher flow rate is always better for hole cleaning, so three flow-rate intervals are discussed separately under the given conditions. When the “dangerous flow rate” (<33 L/s in case 4) is employed, the cuttings bed completely blocks the borehole near the step surface and causes a stuck pipe directly. If the flow rate increases to the “low flow rate” interval (33–35 L/s in case 4), a smaller flow rate instead facilitates borehole cleaning. If the flow rate is large enough to be in the “high flow rate” interval (>35 L/s in case 4), the higher the flow rate, the better the cleaning effect of cuttings beds. Third, an interval of tripping velocity called “dangerous velocity” is proposed, in which the cuttings bed accumulation near the LSDTs is more serious than those of other tripping velocities. As long as the applied tripping velocity is not within the “dangerous velocity” (0.4–0.5 m/s in case 5) interval in the backreaming operation, the risk of the stuck pipe can be controlled validly. Finally, through the factors analyses of the annular geometry, particle properties, and fluid properties in Section 5, it can be found that the “low flow rate”, “high flow rate” and “dangers flow rate” tend to decrease and the “dangerous velocity” tends to increase with the conditions more favorable for hole cleaning. This study has some guiding significance for risk prediction and parameter setting of the backreaming operation.

Experimental investigation and CFD simulation of multiphase flow behavior in air reverse circulation drilling

Insight into dust control performance of a reverse circulation drill bit using multiphase flow simulation

Optimum Design of Large-Diameter Reverse Circulation Drill Bit for Drilling Rescue Wells Using Orthogonal Experimental Method and CFD Simulation

Experimental and Numerical Study on Air Flow Behavior for a Novel Retractable Reverse Circulation Drill Bit of Casing-while-Drilling (CwD)

CFD-DEM Simulation of Reverse Circulation Pneumatic Cuttings Removal during Coal Seam Drilling

Numerical investigation of flow patterns in cuttings transport for extended-reach horizontal wells with rotation drillpipe

Simulation and Analysis of a Split Drill Bit for Pneumatic DTH Hammer Percussive Rotary Drilling

Investigation on the cuttings carrying capacity of a novel retractable drill bit used in casing while drilling with air reverse circulation

Lost Circulation Control for Pump-Injected Reverse Circulation Drilling: Experimental Optimization and Theoretical Analyses

Numerical Investigations on the Effect of a Cuttings Bed Remover on the Cuttings Carrying Capacity in Horizontal Drilling

Rheological effects of air drilling fluids on cuttings transportation in underbalanced drilling

Numerical simulation and experimental study of hole cleaning

Interaction between Pipe Rotation and Cuttings Transport in Extended-Reach Drilling: Mechanism, Model, and Applications

Transportation of cuttings through drill rods during reverse-circulation reaming

Simulation study on cuttings transport of the backreaming operation for long horizontal section wells

Investigation: Cutting Transport Mechanism in Inclined Well Section under Pulsed Drilling Fluid Action

Design and Experimental Study of Negative Pressure Spiral Separation and Reduction Device for Drilling Holes

Study on cuttings removal effect of Effective HydroClean Drill Pipe under different deviation conditions of drill pipe

CFD–DEM approach to investigate the effect of drill pipe rotation on cuttings transport behavior

Numerical investigation of geometry parameters on side-ejector DTH hammer RC bit

Mechanical mechanism and removal effect of efficient vortexing cuttings removal tool