Abstract:Well structures with ultra-long sections have become one of the most applied technologies in the field of shale gas development. While there have been many technical challenges, enhancing the breaking efficiency and stability of polycrystalline diamond compact (PDC) bits has become an essential issue of focus. Since 2013, the well structure in the Duvernay area has been optimized multiple times, and the rate of penetration (ROP) of the entire wellbore has nearly doubled. However, there are significant differences in terms of the performances of different PDC bits, and there is still room for improvement to optimize these drill bits. For this reason, a confined compressive strength test was conducted to obtain the rock mechanical parameters from shale cores extracted from the long horizontal section. Using these data, a finite element model (FEM) was developed with a corresponding scale. A calibration of the elastic-plastic damage constitutive models was then performed using the FEM. The breaking mechanism of three different PDC bits was examined using a "PDC bit-bottom hole" interaction FEM model, facilitating guidance for bit selection and design optimization: (1) The type B PDC bit, which has four blades and 20 cutters, exhibited the highest mechanical specific energy (MSE) and the lowest vibration across three directional mechanical characteristics. This design is recommended for engineering applications. (2) Lower axial vibrations were produced when the CDE was used as the rear element when compared to those when using the BHE. However, an increase within an acceptable range was observed in the TOB and circumferential vibrations. Thus, for redesigning work on the type B bit, the assembly of the CDE is suggested. (3) A decrease in the MSE and vibration in three directional mechanical characteristics was observed when the depth of cut (DOC) was varied between 1.5 and 2.0 mm. A broadening in the range of lateral forces was noted when a DOC of 2.0 mm was used. Therefore, for the redesign of the type B bit, the assembly of CDEs as rear elements at a DOC of 1.5 mm is recommended. In conclusion, a new practical method for the selection and optimization of PDC bit design, based on rock mechanics and the FEM theory, is proposed.

Numerical investigation of geometry parameters on side-ejector DTH hammer RC bit

Optimum Design of Large-Diameter Reverse Circulation Drill Bit for Drilling Rescue Wells Using Orthogonal Experimental Method and CFD Simulation

Experimental and Numerical Study on Air Flow Behavior for a Novel Retractable Reverse Circulation Drill Bit of Casing-while-Drilling (CwD)

Simulation and Analysis of a Split Drill Bit for Pneumatic DTH Hammer Percussive Rotary Drilling

Numerical Investigation of Geometry Parameters for Design of High Performance Ejectors

Experimental investigation and CFD simulation of multiphase flow behavior in air reverse circulation drilling

Investigation on the cuttings carrying capacity of a novel retractable drill bit used in casing while drilling with air reverse circulation

Insight into dust control performance of a reverse circulation drill bit using multiphase flow simulation

Selection and Optimization Design of PDC Bits Based on FEM Analysis for Drilling Long Horizontal Sections of Shale Formations

Percussion characteristic analysis for hydraulic rock drill with no constant-pressurized chamber through numerical simulation and experiment

Design of Diamond Bits Water Passage System and Simulation of Bottom Hole Fluid Are Applied to Seafloor Drill

Numerical Investigations on the Effect of a Cuttings Bed Remover on the Cuttings Carrying Capacity in Horizontal Drilling

Design optimization and feasibility analysis of pneumatic DTH Hammer with self-rotation bit

Experimental Study on Drilling Laws by Self-advancing and Multi-hole Jet Bit

Experimental investigation and optimization of modification during coaxial waterjet-assisted femtosecond laser drilling

Hydraulic structure design and downhole flow field optimization of geophysical drill bits in a limestone stratum

Research on numerical drilling technology of mesh-like cutting PDC bit

Design of internal-chip-removal drill for CFRP drilling and study of influencing factors of drilling quality

Study on cuttings removal effect of Effective HydroClean Drill Pipe under different deviation conditions of drill pipe

Scheme design and flow performance analysis of double-bits combination wire-line coring technology for seafloor drill

Geometrical Optimization of an Inducer with Respect to Rotating Cavitation Generated Radial Forces by Using an Orthogonal Experiment