Abstract:Si3N4/SiC composites containing 0-30 vol% SiC were fabricated by pressureless sintering and sinter-post-HIPing method using fine Si3N4 and nano-sized SiC powders. Specimens reached full density (>96% theoretical density (th. d.)) except the composites made by pressureless sintering which contained a small amount of sintering additives or a large amount of SiC. All composites with 10 mass% sintering additives reached full density (similar to 99% th. d.) by sinter-post-HIPing. The addition of SiC particles greatly influenced the grain morphology of the Si3N4 matrix. The average grain thickness, length and aspect ratio decreased with increasing SiC content because of grain boundary pinning by SiC particles. Also the mechanical properties were markedly dependent upon the fraction of SiC particle reinforcement, as well as matrix grain size and porosity. When the materials were pressureless sintered, the strength of the composite increased with SiC additions below 20 vol%. Further increase in the SIC content resulted in a corresponding decrease in strength. Maximum strength of 1150 MPa was attained at 20 vol% SiC addition. The increase in strength by addition of SiC is due to decrease of grain size of Si3N4 matrix grain size, and the decrease by further increase in SiC content is caused by porosity and SiC agglomerate. On the other hand, toughness decreased monotonically with SiC content. The strength of all samples was enhanced by sinter-post-HIPing without any change in fracture toughness. The strength of sintered samples with 10-15 vol% SiC increased by similar to 20% to 1260 MPa by post-HIPing. The increase in strength by post-HIPing was interpreted as being due to a decrease flaw size.

Fabrication and High-Temperature Mechanical Properties of Sic-Reinforced C11(B)/C40 Structured Mosi2 Matrix Composites

Fabrication And High-Temperature Mechanical Properties Of Sic-Reinforced C11(B)/C40 Structured Mosi2 Matrix Composites

Fabrication And Mechanical Properties Of Mo2b5-Mosi2 Composites

The Microstructure and Mechanical Property of Mo(Si, Al)2-SiC Composite Prepared by Infiltrating Melt Aluminum

Effect of Al Addition on the Microstructure and Properties of MoSi2-5Nb Prepared by Mechanical Alloying

Microstructure and mechanical properties of in situ SiC particulates reinforced MoSi2 matrix composite

Synthesis and properties of MoAlB composites reinforced with SiC particles

Structure–property relationships of SiC reinforced advanced Al–Zn–Mg–Cu alloy

Phase Transformation, Microstructure and Mechanical Properties of Si3n4/Sic Composite

Mechanical Properties of SiC-Whisker-Reinforced MoSi<sub>2</sub> Composites

Microstructure characterization and mechanical properties of in situ synthesized Ti2(Al,Si)C reinforced Al composites

Processing and Mechanical Properties of Multiphase Composites Based on Mo–Si–Al–C System

Mechanical properties and fracture behavior of SiCw reinforced Al–12Ti alloy prepared by bechanical alloying technique

High-Temperature Strength of Sic-Aln Solid-Solutions and Composites As Evaluated by Small Punch Tests

Microstructure and Thermal Conduction Property of SiCp/Al- Si Composite with High Reinforcement Content

The effect of 15 wt% Mo addition on the microstructure and mechanical properties of MoSi2 composite

Fabrication and Mechanical Properties of Si3n4/Sic Nanocomposite with Pressureless Sintering and Sinter-Post-Hiping

Microstructure and Mechanical Properties of MoSi2-X (X = Al, B, Nb) Alloys Fabricated by MA-PDS Process.

Mechanical and thermal expansion behavior of hybrid aluminum matrix composites reinforced with SiC particles and short carbon fibers

Microstructure, Mechanical, and Thermal Properties of in Situ-Synthesized (zrb2+sic)/zr2[al(si)]4c5 Composites

Mechanical and Electrical Properties of Nano Al-Matrix Composites Reinforced with SiC and Prepared by Powder Metallurgy