Abstract:Next to aluminum-based porous alloys, porous Mo-Si-B intermetallic compounds are the most promising filtration and separation material to handle harsh service conditions of ultra-high-temperature corrosive environment. Porous Mo3Si-Mo5Si3-Mo5SiB2 intermetallics were fabricated by a two-step method of spark plasma sintering (SPS) and homogenization treatment (HT) using Mo, Si, and B as the starting powders. In addition, the evolution of the pore/skeleton structure and compressive behavior of porous Mo3Si-Mo5Si3-Mo5SiB2 intermetallic compounds by the two-step method was investigated. In SPS, the phase transformation included a solid–liquid reaction and solid–solid diffusion, and the pore structure changed significantly with the increase of sintering temperature. By HT, smooth skeletons and size centralized pores were obtained. With the increase in the HT time, the precise control of pore/skeleton structure parameters was achieved while simultaneously maintaining stable porosity. Combined SPS+HT led to a wide range of porosities, and pore/skeleton parameters were controlled by the sintering temperature and SPS pressure. Compression test results indicate that the porous Mo3Si-Mo5Si3-Mo5SiB2 intermetallics do not exhibit a plastic deformation ability at room temperature and that the transgranular cleavage fracture dominates the crack propagation in the skeletons. The quantitative relationship between porosity and compressive strength was established by σ c = σ c0 × (1 – ρ)1/J . The effect of HT on the pore structure factor J was revealed: at constant porosity, the strength can be increased by the increase in the J value via HT.

Fabrication And Mechanical Properties Of Mo2b5-Mosi2 Composites

Microstructure, Compressive Performance and Wear Resistance of Pure Molybdenum Additively Manufactured Via Laser Powder Bed Fusion

Preparation of Mosi2-X(X = B, Al, Nb) Alloys by Mechanical Alloying and Pulse Discharge Sintering Process

Preparation of MoSi<SUB>2</SUB>-X(X=B, Al, Nb) Alloys by Mechanical Alloying and Pulse Discharge Sintering Process

Microstructure and Mechanical Properties of Unalloyed Molybdenum Fabricated Via Wire Arc Additive Manufacturing

Microstructure and Mechanical Properties of MoSi2-X (X = Al, B, Nb) Alloys Fabricated by MA-PDS Process.

Fabrication and High-Temperature Mechanical Properties of Sic-Reinforced C11(B)/C40 Structured Mosi2 Matrix Composites

Effect of Al Addition on the Microstructure and Properties of MoSi2-5Nb Prepared by Mechanical Alloying

Preparation of MoSi2-x (X=B, Al, Nb) Alloys by MA-PDS Process.

Fabrication And Mechanical Properties Of Al2o3-Ti3sic2 Composites By Sps

Pore/skeleton structure and compressive strength of porous Mo3Si-Mo5Si3-Mo5SiB2 intermetallic compounds prepared by spark plasma sintering and homogenization treatment

Preparation and Mechanical Properties of Laminated Zirconium Diboride/molybdenum Composites Sintered by Spark Plasma Sintering

Processing and Mechanical Properties of Multiphase Composites Based on Mo–Si–Al–C System

Synthesis of a novel MoSS+Mo5SiB2+Mo5Si3 based Mo–Si–B alloy and its enhanced fracture toughness

Microstructure Evolution and Wear Properties of Bulk MoSi2 Fabricated by Field Activated Sintering

Effect of MoS2 on the Tribological Properties of in Situ Fe3Al-20 Wt% Al2O3-4 Wt% Cr Composites

Fabrication and Mechanical Properties of Al<sub>2</sub>O<sub>3</sub>-Ti<sub>3</sub>SiC<sub>2</sub> Composites by SPS

The Microstructure and Mechanical Property of Mo(Si, Al)2-SiC Composite Prepared by Infiltrating Melt Aluminum

Microstructure and compression properties of fine Al2O3 particles dispersion strengthened molybdenum alloy

The progress in preparation and properties of multiphase Mo-Si-B alloy