Abstract:Molybdenum (Mo), a refractory material, boasts an elevated melting point of 2610 °C and is predominantly synthesised through powder metallurgy at high temperatures reaching 2000 °C, necessitating the use of liquid phase sintering (LPS) technique. This study investigates the LPS of Mo with varying proportions of NiCu binders, aiming to understand the mechanism of intermetallic formation and to manufacture low-cost, dense, intermetallic-free and near-net-shape Mo-base alloys. Employing the manufacturing design paradigm for 90 W-10(NiCu) tungsten heavy alloys (WHAs) and utilising conventional powder metallurgy techniques, Mo-based 90Mo-10(NiCu) alloys were synthesised. Initial findings indicate that the densification of Mo-compacts increases with increasing the NiCu ratio in the binder phase. However, an excess of Ni results in the loss of structural rigidity and geometric distortion during sintering. In Ni-rich alloys, two distinct liquid phases, Ni-rich and Cu-rich, emerge at sintering temperatures. These phases exhibit different solubilities for Mo and solidify into a dual-phase matrix. Intriguingly, in contrast to WHAs, 90Mo-10(NiCu) alloys with a Ni-rich composition manifested irregular Mo particles, a dual-phase matrix, and δ -MoNi intermetallic compound formation. The formation of the intermetallic compound can be avoided by reducing the solubility of Mo in the Ni-rich liquid during sintering. Microstructural evolution and distortion are analysed using stereological quantification of various microstructural parameters. It reveals that alloys with low Mo solubility, high connectivity and high dihedral angle maintain their structural rigidity and resist distortion. Both micro-hardness and bulk hardness increased with increasing NiCu ratios in the binder phase. Based on the present results, a mechanism for liquid phase sintering in the 90Mo-10(NiCu) system in the presence of two liquid phases is postulated.

Preparation of MoSi2-x (X=B, Al, Nb) Alloys by MA-PDS Process.

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Preparation of nanostructural oxide dispersion strengthened (ODS) Mo alloy by mechanical alloying and spark plasma sintering, and its characterization

Effects of Doped Elements (Si, Cr, W and Nb) on the Stability, Mechanical Properties and Electronic Structures of MoAlB Phase by the First-Principles Calculation

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

The process and mechanical properties of Nb–Si–Mo–Ti alloy prepared by spark plasma sintering

Processing of molybdenum disilicide

Microstructure and compression properties of fine Al2O3 particles dispersion strengthened molybdenum alloy

Synthesis, Microstructure and Mechanical Properties of a MoAlB Ceramic Prepared by Spark Plasma Sintering from Elemental Powders

Experimental investigation on powder processing and its flow properties of AlSi10Mg alloy with niobium carbide for additive manufacturing

Synthesis and properties of MoAlB composites reinforced with SiC particles

Gas-Atomized Nickel Silicide Powders Alloyed with Molybdenum, Cobalt, Titanium, Boron, and Vanadium for Additive Manufacturing

Preparation and enhanced oxidation behavior of microalloyed Mo5SiB2 alloy at 1300 °C

High Temperature Oxidation Performance of an Additively Manufactured Mo–9Si–8B Alloy

Sintering behaviour of liquid phase sintered 90Mo-10(Ni Cu) alloys

Effect of silicon addition on microstructure and mechanical properties of a high strength Ti-4Al-4Mo-4Sn alloy prepared by powder metallurgy

Synthesis Mechanism of Amorphous Si2BC3N Powders: Structural Evolution of 2si‐bn‐3c Mixtures During Mechanical Alloying

Microstructure and properties of in-situ Al–Si/Al2O3 composites prepared by displacement reaction

Microstructures and mechanical properties of reactive spark plasma-sintered ZrB2–SiC–MoSi2 composites

Powder Metallurgical Processing of Al–5 wt% Cu Matrix Composites Reinforced with MoSi2 and WSi2 Particulates

Effect of Processing Route on Microstructure and Mechanical Properties of an Al-12Si Alloy