Abstract:Molybdenum-silicon-boron (Mo-Si-B) alloy, which is considered a promising material for manufacturing aemengines, is mainly processed by methods including arc smelting and powder metallurgy. Selective laser melting (SLM), as the most commonly used processing method in additive manufacturing at present, provides another option for processing Mo-Si-B alloy. To study defects appearing during SLM of Mo-Si-B alloy, the effects of SLM parameters on the relative density were investigated based on orthogonal tests. It is found that the layer thickness has the largest influence on the relative density, followed by the laser power and hatch spacing, while the scanning speed exerts the smallest influence. By regulating SLM parameters, compact Mo-Si-B samples with a relative density larger than 99% can be obtained. Furthermore, a large number of intergranular cracks are found in Mo-Si-B alloy subjected to SLM, which can be regulated by preheating the substrate. When preheating the substrate at 400 degrees C, cracks on a horizontal section almost disappear and the reduction of cracks improves the compressive properties of the samples to some extent. The compressive strength of the samples without substrate preheating is 1065 MPa and it reaches 1610 MPa when preheating the substrate at 400 degrees C. The microhardness of the samples is about 360 HV, where the microhardness of a longitudinal section is higher than that of the horizontal section. Grains on each section have unique characteristics. For the longitudinal section, grains are columnar crystals along the building direction and the average grain size is about 8.69 mu m. In terms of the horizontal section, grains are irregular and the average grain size is 3.12 mu m. There are < 001 > textures in the main phases alpha-Mo of each section, and the existence of textures may lead to anisotropic properties of the samples.

Microstructure and Mechanical Properties of MoSi2-X (X = Al, B, Nb) Alloys Fabricated by MA-PDS Process.

Preparation of MoSi2-x (X=B, Al, Nb) Alloys by MA-PDS Process.

Preparation of MoSi<SUB>2</SUB>-X(X=B, Al, Nb) Alloys by Mechanical Alloying and Pulse Discharge Sintering Process

Preparation of Mosi2-X(X = B, Al, Nb) Alloys by Mechanical Alloying and Pulse Discharge Sintering Process

Effect of Al Addition on the Microstructure and Properties of MoSi2-5Nb Prepared by Mechanical Alloying

Fabrication And Mechanical Properties Of Mo2b5-Mosi2 Composites

Regulation of Microstructures and Properties of Molybdenum‑silicon‑boron Alloy Subjected to Selective Laser Melting

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Preparation of nanostructural oxide dispersion strengthened (ODS) Mo alloy by mechanical alloying and spark plasma sintering, and its characterization

Preparation of Intermetallic Compound MoSi2 by Mechanical Alloying Method

Microstructure and Valence Bonds of Si-B-C-N-Al Powders Synthesized by Mechanical Alloying

Microstructure and compression properties of fine Al2O3 particles dispersion strengthened molybdenum alloy

Fabrication and High-Temperature Mechanical Properties of Sic-Reinforced C11(B)/C40 Structured Mosi2 Matrix Composites

Microstructure and Thermal Stability of Amorphous SiBCNAl Powders Fabricated by Mechanical Alloying

The Multi-Scale Microstructure and Strengthening Mechanisms of Mo-12Si-8.5BxZr (at.%) Alloys

Characterization of Mo–Si–B Nanocomposite Powders Produced Using Mechanical Alloying and Powder Heat Treatment

Synthesis of Mosi2 by Mechanical Alloying

Microstructure and Mechanical Properties of Lanthanum Oxide-Doped Mo–12Si–8.5B(at%) Alloys

Tailoring the microstructure of molybdenum disilicide matrix composites with Nb additions

Synthesis, Microstructure and Mechanical Properties of a MoAlB Ceramic Prepared by Spark Plasma Sintering from Elemental Powders