Abstract:A detailed knowledge of structural evolution during mechanical alloying (MA) is of interest and critical for understanding of synthesis mechanism, optimization of milling process, and control of milling products. The structural evolution of the 2Si-BN-3C mixture with a molar ratio of Si:BN:C = 2:1:3 during MA was studied by investigating the changes of phases, morphologies, elemental distributions, microstructures, and chemical bond states using XRD, SEM-EDS, TEM, XPS, and Raman. With the increases in milling time, the particle sizes of the milled 2Si-BN-3C powders first decrease to submicrometers (similar to 1 hour), slightly increase afterward (similar to 3 hours), and eventually decrease to nanoscales gradually reaching equilibrium (>= 10 hours). Depending on the intrinsic crystal structures of themselves, h-BN and graphite are almost amorphized after milling of 10 hours, while amorphization of c-Si takes at least 20 hours. The same milling parameters can provide amorphous Si2BC3N powders, but incompletely amorphous (partially crystalline) SiC powders, which is mainly due to the dilution effect of B and N atoms on the atomic concentration of Si and C hindering the microdiffusion and subsequent mechanochemical reaction of Si and C. Crystallite refinement-induced amorphization is the major synthesis mechanism of amorphous Si2BC3N powders. This work would offer more insight into the MA synthesis of multiple component materials, especially Si-based brittle systems.

Microstructure and Valence Bonds of Si-B-C-N-Al Powders Synthesized by Mechanical Alloying

Microstructure and Thermal Stability of Amorphous SiBCNAl Powders Fabricated by Mechanical Alloying

Structural and microstructural characterization of SiB0.5C 1.5N0.8Al0.3 powders prepared by mechanical alloying using aluminum nitride as aluminum source

Synthesis Mechanism of Amorphous Si2BC3N Powders: Structural Evolution of 2si‐bn‐3c Mixtures During Mechanical Alloying

Amorphization in the AlC System by Mechanical Alloying

Carbon content-dependent microstructures, surface characteristics and thermal stability of mechanical alloying derived SiBCN powders

Microstructures and Mechanical Properties of SiBCNAl Ceramics Produced by Mechanical Alloying and Subsequent Hot Pressing

Microstructure and thermal stabilities in various atmospheres of SiB0.5C1.5N0.5 nano-sized powders fabricated by mechanical alloying technique

Study on the nano-crystalline and amorphous Al-Pb series powders synthesized by mechanical alloying

Formation of nanocrystalline and amorphous phase of Al-Pb-Si-Sn-Cu powder during mechanical alloying

Boron‐dependent Microstructural Evolution, Thermal Stability, and Crystallization of Mechanical Alloying Derived SiBCN

Preparation of Cbnp/Nicral Nanostructured Composite Powders by A Step-Fashion Mechanical Alloying Process

Microstructure and high-temperature properties of SI-B-C-N MA-powders and ceramic

Characterization of Mo–Si–B Nanocomposite Powders Produced Using Mechanical Alloying and Powder Heat Treatment

Mechanical alloying derived SiBCN-Ta4HfC5 composite ceramics: study on amorphous transformation mechanism

Synthesis of NiAl(Cr,Nb) Powder by Mechanical Alloying

Synthesized by Ball Milling Al-Pb-Si-Sn-Cu Nanocrystalline Powder

Effect of SiC particulate on the microstructure of Al-6Ti-6Nb matrix composites fabricated by mechanical alloying technique

Microstructure and Morphology of Al-Pb Bearing Alloy Synthesized by Mechanical Alloying and Hot Extrusion

Microstructure and Mechanical Properties of MoSi2-X (X = Al, B, Nb) Alloys Fabricated by MA-PDS Process.

Microstructure And Mechanical Properties Of Al-Sic Nanocomposites Synthesized By Surface-Modified Aluminium Powder