Abstract:In this study, structural, morphological, thermal and magnetic properties of amorphous-nanocrystalline Fe 70 Cr 10 Nb 10 B 10 (at.%) alloy are discussed. The formation and evaluation of amorphous-nanocrystalline structures of the alloy were followed by XRD, SEM-EDX, TEM, DTA, and VSM techniques. After 50 h of milling Cr, Nb, and B were completely dissolved into the Fe lattice forming 82% of the amorphous phase of the alloy. A gradual dissolution of the alloying elements also increased the lattice parameters concurrently. The lattice parameters reached a maximum value of 2.908 Å after 20 h of milling and then leveled off to a value of 2.891 Å at the end of 50 h of milling. Based on the XRD data, crystallite size and lattice strain of the alloy were calculated as 3.2 nm and 3.34% respectively. TEM analyses revealed that the alloy particulates comprised needle-shaped nanoparticles of an average size of 21 nm. The room temperature magnetic hysteresis loops showed that the increased duration of milling decreased the saturation magnetization from 91 to 24 emu/g. This was mainly due to the upsurge on the amorphous phase content in the alloy as the milling progressed. The increase in amorphous phase content and the subsequent reduction of the saturation magnetization were due to the inter-diffusion of the non-ferromagnetic Cr and B atoms into the Fe lattice. Thermal studies revealed that around 350 °C the amorphous phase of the alloy began crystallizing. The magnetic saturation of the heat-treated alloy also increased with the growth in the crystalline phases. The 50 h milled sample annealed at 700 °C was found to have the highest magnetic anisotropy as observed from the temperature-dependent zero-field cooled and field cooled magnetization measurements. The high-pressure X-ray diffraction measurements revealed that the amorphous state of the alloy remained stable up to 11.3 MPa. It also revealed the structural similarities of the Fe 70 Cr 10 Nb 10 B 10 alloy with those of the Fe 70 M 10 B 20 (M = Nb and Cr) types. For all practical purposes, the microstructural stability under high compressive pressure represents the consolidation properties of the nanostructured magnetic materials since both pressure and temperature-induced phase transformations are the primary controlling factors for the specific magnetization properties of the alloy.

Mechanical alloying derived SiBCN-Ta4HfC5 composite ceramics: study on amorphous transformation mechanism

Amorphization in the AlC System by Mechanical Alloying

Synthesis Mechanism of Amorphous Si2BC3N Powders: Structural Evolution of 2si‐bn‐3c Mixtures During Mechanical Alloying

Microstructural evolution and mechanical properties of in situ nano Ta4HfC5 reinforced SiBCN composite ceramics

Comparative study on the microstructure evolution and crystallization behavior of precursor-derived and mechanical alloying derived SiBCN

Crystallization Kinetics of Co-Finemet Amorphous Alloys and Magnetic Properties of Nanocrystalline Powder Cores

The Crystallization Kinetics Study of Finemet-Co Amorphous Alloys

The Amorphous-To-Nanocrystalline Transformation In Fe73.5cu1nb3si13.5b9 Studied By Thermogravimetry Analysis

Formation of Nanocrystalline Fcc Phase by Mechanically Driven Crystallization

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Nanocrystallization Kinetics of Amorphous Fe73.5Cu1Nb3−xMoxSi13.5B9 (x=1, 2, 3) Alloys

Preparation of ti-al based nanophase composite powder by mechanical alloying

Microstructure evolution and phase transformation of amorphous BCN–SiC composites prepared by two synthetic routes

Evolution from Amorphous to Nanocrystalline and Corresponding Magnetic Properties of Fe-Si-B-Cu-Nb Alloys by Melt Spinning and Spark Plasma Sintering

Atomic level simulation of amorphous/nanocrystalline transition behavior in the Fe based amorphous alloys

Mechanical Alloying, Fine Structure and Thermal Decomposition of Nanocrystalline Fcc-Fe60cu40

Effects of Ti on the Microstructural Evolution and Mechanical Property of the SiBCN-Ti Composite Ceramics

Study on mechanical alloying behavior and thermal stability of HfMoNbTaTi refractory high-entropy alloy

Grain refinement mechanism of soft-magnetic alloys with nanocrystals embedded in amorphous matrix

Synthesis and characterization of amorphous-nanocrystalline Fe70Cr10Nb10B10 powders by mechanical alloying

Mechanical Alloying Effect on the Structure of Fe-Al-(Si) Alloy