Abstract:Next to aluminum-based porous alloys, porous Mo-Si-B intermetallic compounds are the most promising filtration and separation material to handle harsh service conditions of ultra-high-temperature corrosive environment. Porous Mo3Si-Mo5Si3-Mo5SiB2 intermetallics were fabricated by a two-step method of spark plasma sintering (SPS) and homogenization treatment (HT) using Mo, Si, and B as the starting powders. In addition, the evolution of the pore/skeleton structure and compressive behavior of porous Mo3Si-Mo5Si3-Mo5SiB2 intermetallic compounds by the two-step method was investigated. In SPS, the phase transformation included a solid–liquid reaction and solid–solid diffusion, and the pore structure changed significantly with the increase of sintering temperature. By HT, smooth skeletons and size centralized pores were obtained. With the increase in the HT time, the precise control of pore/skeleton structure parameters was achieved while simultaneously maintaining stable porosity. Combined SPS+HT led to a wide range of porosities, and pore/skeleton parameters were controlled by the sintering temperature and SPS pressure. Compression test results indicate that the porous Mo3Si-Mo5Si3-Mo5SiB2 intermetallics do not exhibit a plastic deformation ability at room temperature and that the transgranular cleavage fracture dominates the crack propagation in the skeletons. The quantitative relationship between porosity and compressive strength was established by σ c = σ c0 × (1 – ρ)1/J . The effect of HT on the pore structure factor J was revealed: at constant porosity, the strength can be increased by the increase in the J value via HT.

Pore/skeleton structure and compressive strength of porous Mo3Si-Mo5Si3-Mo5SiB2 intermetallic compounds prepared by spark plasma sintering and homogenization treatment

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Preparation, Characterization and Designing of Porous Ti–6Al–4V Through Metal Injection Molding Without Space Holder

The Microstructure and Mechanical Property of Mo(Si, Al)2-SiC Composite Prepared by Infiltrating Melt Aluminum

Microstructures and performances of pressureless sintered MoSi2-Al2O3 composites

Review of Research Progress on Mo-Si-B Alloys

Microstructures and mechanical properties of reactive spark plasma-sintered ZrB2–SiC–MoSi2 composites

Compression Behaviour of Porous Mof/Ti-12Nb-18Zr Composite with Short Mo Fibers

The process and mechanical properties of Nb–Si–Mo–Ti alloy prepared by spark plasma sintering

The progress in preparation and properties of multiphase Mo-Si-B alloy

Processing and Mechanical Properties of Multiphase Composites Based on Mo–Si–Al–C System

A novel sintering additive system for porous mullite-bonded SiC ceramics: High mechanical performance with controllable pore structure

The effect of 15 wt% Mo addition on the microstructure and mechanical properties of MoSi2 composite

Microstructure and mechanical properties of a Mo-toughened Mo 3 Si-based in situ nanocomposite

Effects of Mo Contents on the Microstructure, Properties and Cytocompatibility of the Microwave Sintered Porous Ti-Mo Alloys.

Preparation and Mechanical Properties of Laminated Zirconium Diboride/molybdenum Composites Sintered by Spark Plasma Sintering

Strengthening mechanism and anisotropy of mechanical properties of Si3N4p/Al-Mg-Si composites fabricated by sintering and extrusion

Phase composition and mechanical properties of in-situ synthetic Mo-Si compound composites

Fabrication And Mechanical Properties Of Mo2b5-Mosi2 Composites

The Effect of Heat-Treatment on Microstructure and Fracture Toughness of Intermetallics in Mo-Si System

Strengthening and toughening of MoSi2 and MoSi2-base dmaterials