Abstract:Al2O3-Cr2O3 refractories have excellent slag corrosion resistance and can adapt to the oxidation/reduction atmosphere in the smelting reduction ironmaking furnace. However, Al2O3-Cr2O3 refractories have poor mechanical properties and sintering properties. In order to improve the mechanical properties of Al2O3-Cr2O3 materials, the CaAl12O19 reinforced Al2O3-Cr2O3 composites were prepared by pressureless sintering process, and the influences of CaO content on the sintering properties, mechanical properties, and microstructure evolution of the composites were studied. The results show that a small amount of CaO can significantly improve the compactness of the composites, which is mainly due to the formed sheet-like CA6 fill the gap between the solid solutions, and reduces the porosity of the composites. In addition, the sheet-like CA6 makes the connection between solid solutions closer, and the intergranular fracture gradually transforms into a mixed mode of intergranular and transgranular fracture. The best mechanical propertie is observed at S4 with the CaO content of 2 wt.%. Compared with sample S0 without CaO, the hardness, compressive strength and flexural strength of the S4 were increased by 35.19 %, 49.69 %, and 68.34 %, respectively. The addition of excessive CaO will deteriorate the mechanical properties of the composites, because the formation of a large number of layered CA6 increases the porosity of the composites. Furthermore, a small amount of CaO addition can significantly improve the thermal shock resistance of the composites. After 10 and 20 thermal shock cycles, the strength loss rates of S4 are only 5.83 % and 8.74 %, respectively.

Microstructures and performances of pressureless sintered MoSi2-Al2O3 composites

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Effect of WSi2 content on oxidation behavior of MoSi2-20 vol% Al2O3 composites

Synthesis and properties of MoAlB composites reinforced with SiC particles

Effect of Al2O3 addition on properties of non-sintered SiC–Si3N4 composite refractory materials

Pressure Sintering, Structure and Some Properties of SiC–Al Composite Materials

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Pore/skeleton structure and compressive strength of porous Mo3Si-Mo5Si3-Mo5SiB2 intermetallic compounds prepared by spark plasma sintering and homogenization treatment

Improving thermal conductivity of Al/SiC composites by post-oxidization of reaction-bonded silicon carbide preforms

Effects of in situ Mg-Sialon and β-Sialon on the microstructure and properties of MgAl2O4-SiC composites

Oxidation Resistance and Heat Transfer Simulation of MoSi2-based Coatings on Carbon Fiber Reinforced C-Al2O3 Aerogel Composite

Microstructure and mechanical properties of CaAl12O19 reinforced Al2O3-Cr2O3 composites

Microstructures and enhanced mechanical properties of (Al3Ti+Al2O3)/Al–Si composites with co-continuous network structure prepared by pressure infiltration

Microstructure and electrical contact behavior of Al2O3–Cu/30W3SiC(0.5Y2O3) composites

Preparation, microstructure, stability in magnesium metallurgy environment of SiC composites

Microstructure refinement and oxidation behavior improvement in Mo modified TiAl4822 alloy prepared by vacuum sintering

In Situ Synthesis of (Mo,Cr)Si2 Composites by Spark Plasma Sintering

Study on Micro-structure and Properties of Al2O3/SiC Ceramics by Pressureless Sintering in Air

Microstructure and tribological properties evolution of Ni-Mo-SrSO 4 composites as a function of Mo contents at different temperatures

Effect of Mo/Si Ratio on the Microstructure and Oxidation Resistance of Si-Mo Coating for C/C Composites

Effect of Zr2Al4C5 Content on the Mechanical Properties and Oxidation Behavior of ZrB2-SiC-Zr2Al4C5 Ceramics