Abstract:The influence of Mo (10‐40at.%) additions to Cr‐8at.%Si was systematically studied by producing arc melted alloys and analyzing the as‐cast and annealed microstructures as well as the oxidation resistances. The majority of the alloys contained a solid solution A2 matrix with the intermetallic A15 = (Cr,Mo)3Si phase. The oxidation resistance was tested by thermogravimetric analysis (TGA) at 1200 °C in air for 50 and 100 h. Samples were characterized by XRD, SEM and EPMA (WDS). The studied Cr‐xMo‐8Si alloy series showed a beneficial effect of Mo on the corrosion behavior of the annealed arc melted alloys exposed at 1200 °C in air. An increased amount of A15 led to the formation of a continuous SiO2 scale beneath the Cr2O3 layer during high temperature exposure. The internal SiO2 layer inhibited further internal oxidation of the A15 phase. Prior annealing also influenced the oxidation behavior of the alloys. Higher annealing temperatures, resulted in an overall reduced fraction of the A15 phase, as well as coarsening, but also showed a more uniform size and distribution of the precipitates, which seems to benefit the formation of a protective duplex oxide scale. Cr‐25Mo‐8at.%Si annealed at 1350 °C for 100 h, showed the most promising oxidation behavior after exposure in air at 1200 °C for 100 h. For all of the investigated Mo contents, no nitridation was observed when compared to the Cr‐8Si reference composition. The oxide scale adhesion also was improved. For Mo >25 at.% no spallation was observed. Evaluation of the TGA data showed it follows the paralinear law, with both the growth rate, kp, and volatilization rate, kv, of Cr2O3 being reduced by adding 10‐25 at.% Mo. A binary Cr/Mo‐Si phase diagram was generated for the studied alloy series in order to determine accurate annealing conditions and estimate the stability range of the metastable σ phase. This article is protected by copyright. All rights reserved.

Microstructure refinement and oxidation behavior improvement in Mo modified TiAl4822 alloy prepared by vacuum sintering

Effect of Mo Content on Microstructure and Properties of 00cr12ni9mo (x) Cu2Ti Maraging Stainless Steel

Effect of 2–6 At.% Mo Addition on Microstructural Evolution of Ti-44Al Alloy

Microstructures and tensile properties of Ti<sub>2</sub>AlNb and Mo-modified Ti<sub>2</sub>AlNb alloys fabricated by hot isostatic pressing

Influence of TiC contents on the microstructure, mechanical properties, and oxidation behavior of Mo–10Si–8B alloys

Influence of Mo addition on microstructural and mechanical characteristics of TiXMo5Cu alloys manufactured by powder metallurgy

Microstructure and compression properties of fine Al2O3 particles dispersion strengthened molybdenum alloy

Microstructure refinement and second phase particle regulation of Mo−Y2O3 alloys by minor TiC additive

Microstructural evolution and grain refinement in an intermetallic titanium aluminide alloy with a high molybdenum content

High-temperature Oxidation Behaviour of SPS-prepared Mo and Mo–5Ta Alloys

Preparation and enhanced oxidation behavior of microalloyed Mo5SiB2 alloy at 1300 °C

Influence of Mo doping on the tribological behavior of Ti3AlC2 ceramic at different temperatures

Effect of Molybdenum on Isothermal Oxidation Behavior of 4th Generation Nickel-Based Single Crystal Superalloys

High-temperature steam oxidation behavior of an FeCrAl alloy with controlled addition of Mo

The effects of oxygen addition on microstructure and mechanical properties of Ti-Mo alloys for biomedical application

Effect of molybdenum on cyclic oxidation behavior of 4 th generation nickel-based single crystal superalloys

Effect of silicon addition on microstructure and mechanical properties of a high strength Ti-4Al-4Mo-4Sn alloy prepared by powder metallurgy

THE INFLUENCE OF Mo‐CONTENT AND ANNEALING ON THE OXIDATION BEHAVIOUR OF ARC‐MELTED Cr‐xMo‐8Si ALLOYS

Influence of Al and Mo on microstructure and tribological behaviors of Co-based superalloy

Microalloying effects of Ho on microstructure evolution and high temperature properties of Ti46Al4Nb1Mo alloy

Strengthening the grain boundary of Mo alloy via little TiC addition