Abstract:Ti-4Al-4Mo-4Sn-xSi (wt%) (x = 0, 0.2, 0.5) alloys were fabricated by hot extrusion of compacts of blends of TiH2, AlMo60 master alloy and other required elemental powders followed by heat treatments involving vacuum annealing, solution treatment, air cooling and aging. The microstructure of the alloys consists of α plates, lamellae of α and transformed β structure (βt), βt blocks as well as grain boundary α layers. With the addition of 0.2 wt%Si, the Si atoms exist in equal concentration in both α and βt regions as solute atoms, and they retard the growth of α phase, causing a decrease of the average thickness of α plates and lamellae and slight increase of the volume fraction of βt lamellae and blocks. The solid solution strengthening and enhanced α/β interface hardening brought by the 0.2 wt%Si cause the yield strength of the Ti-4Al-4Mo-4Sn alloy to increase significantly from 1030 to 1130 MPa with a slight decrease of the tensile ductility (7.4% vs 6.8%) and without changing the fracture behavior. With the addition of 0.5 wt%Si, the extra Si causes nanometer sized silicide (Ti5Si3) precipitates to form in both α and βt regions and further microstructural refinement. The additional α/β interface hardening and precipitation hardening cause the yield strength of the alloy to increase further to 1177 MPa, but the tensile ductility deteriorates clearly with the elongation to fracture decreasing to 4.9%. The main reason for this ductility decrease is the premature fracture of grain boundary α layers caused by the higher flow stress which can induce more strain localization at the grain boundary α layers.

The effect of 15 wt% Mo addition on the microstructure and mechanical properties of MoSi2 composite

Effect of Molybdenum on the Impact Toughness of Heat-Affected Zone in High-Strength Low-Alloy Steel

Microstructure and mechanical properties of a Mo-toughened Mo 3 Si-based in situ nanocomposite

Preparation, microstructure and mechanical properties of MoAlB-0.15% Si ceramics with superior strength and toughness

Synthesis and properties of MoAlB composites reinforced with SiC particles

Effects of Mo Addition on Microstructure of a 4th Generation Ni-based Single Crystal Superalloy

Synergistic effect of Zr and Mo on precipitation and high-temperature properties of Al-Si-Cu-Mg alloys

Effect of 2–6 At.% Mo Addition on Microstructural Evolution of Ti-44Al Alloy

Effect of Si Content on the Uniaxial Tensile Behavior of Mo-Si Solid Solution Alloys

The Effect of Simultaneous Si and Ti/Mo Alloying on High-Temperature Strength of Fe3Al-Based Iron Aluminides

High temperature tribological behavior of Mo–12Si–8.5B alloy reinforced with MoAlB ceramic

Effect of Mo on microstructural stability of a 4th generation Ni-based single crystal superalloy

Effect of Si on Fe-rich intermetallic formation and mechanical properties of heattreated Al-Cu-Mn-Fe alloys

Optimization of Zr and Mo element on room-temperature fracture toughness and the integrity of oxide film

Low temperature deformation of MoSi$_2$ and the effect of Ta, Nb and Al as alloying elements

Effect of Mo on the coherent interface features of γ′-phase strengthened Co-based superalloys

Effect of microstructures on mechanical properties of Ti‐6.5Al‐2Sn‐4Zr‐4Mo‐1W‐0.2Si alloy

Effect of silicon addition on microstructure and mechanical properties of a high strength Ti-4Al-4Mo-4Sn alloy prepared by powder metallurgy

Microstructures and performances of pressureless sintered MoSi2-Al2O3 composites

Effects of metalloid Si on the microstructure and mechanical properties of Fe36Ni36Cr10Mo1Al17-XSiX alloys

Microstructure and compression properties of fine Al2O3 particles dispersion strengthened molybdenum alloy