Abstract:Abstract Silicon and molybdenum ( SiMo ) ductile iron is commonly used for exhaust manifolds because these components experience thermal cycling in oxidizing environment, which requires resistance to fatigue during transient thermomechanical loads. Previous studies have demonstrated that alloying elements, such as Al , to SiMo ductile iron reduces the amount of surface degradation during static high-temperature exposure. However, deterioration of sphericity of the graphite nodules and a decrease in ductility could affect the tendency of cracking during thermal cycling. In this article, the effect of Al alloying on static and transient thermomechanical behavior of SiMo ductile iron was investigated to optimize the amount of Al alloying. A thermodynamic approach was used to confirm the effect of the Al alloying on the phase transformations in two SiMo cast irons, alloyed by 1.8% Al and 3% Al . These two alloys were cast in a laboratory along with the baseline SiMo ductile iron. Several experimental methods were used to evaluate the dimensional stability, physical properties, static oxidation, and failure resistance during constrained thermal cycling testing to compare their high-temperature capability. Experimental results verified that Al alloying increases the temperature range and decreases volume change during eutectoid transformation, which together with enhancement of oxidation protection improved the dimensional stability. Thermocycling tests showed that the number of cycles to failure depends on the amount of Al alloying and the applied high-temperature exposure during each cycle. SEM/EDX, high-resolution TEM and μCT analysis were used to verify the mechanism resulting from the Al alloying protection. It was shown that an optimal level of Al alloying for balancing oxidation and thermal cracking resistance depends on thermomechanical conditions of application.

Low temperature deformation of MoSi$_2$ and the effect of Ta, Nb and Al as alloying elements

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

High-Temperature Rheological Behavior and Microstructure Evolution of Mo-12Si-8.5B Alloy Reinforced by Layered Mo2TiAlC2 Phase

Effect of Si Content on the Uniaxial Tensile Behavior of Mo-Si Solid Solution Alloys

High-Temperature Creep and Oxidation Behavior of Mo-Si-B Alloys with High Ti Contents

Mo effect on the phase stability and room-temperature fracture toughness of Nb/Nb5Si3 in-situ composites

A new approach to understand the deformation behavior and strengthening mechanism of molybdenum alloy: From single crystal to polycrystal

Tensile properties of MOSi2 at elevated temperatures

Microstructure and High Temperature Deformation Behavior of the Mo-ZrO 2 Alloys

High temperature deformation behaviors of Ti-45Al-2Nb-1.5V-1Mo-Y alloy

Nanoindentation of single crystalline Mo: Atomistic defect nucleation and thermomechanical stability

The effect of 15 wt% Mo addition on the microstructure and mechanical properties of MoSi2 composite

Ultra-high Temperature Mo–Si–B Alloys — Synthesis, Microstructural and Mechanical Characterization

Experimental studies on the dynamic tensile behavior of Ti–6Al–2Sn–2Zr–3Mo–1Cr–2Nb–Si alloy with Widmanstatten microstructure at elevated temperatures

The Microstructure and Mechanical Property of Mo(Si, Al)2-SiC Composite Prepared by Infiltrating Melt Aluminum

Insights into the Deformation Mechanisms of an Al1Mg0.4Si Alloy at Cryogenic Temperature: an Integration of Experiments and Crystal Plasticity Modeling

High temperature tribological behavior of Mo–12Si–8.5B alloy reinforced with MoAlB ceramic

First principles study on the phase stability and mechanical properties of MoSi2 alloyed with Al, Mg and Ge

Effect of Mo Addition on Microstructure and Properties of Nb/Nb<sub>5</sub>Si<sub>3</sub> In-Situ Composite

Microstructure Evolution in TiAl Alloyed with Si

Control of High-Temperature Static and Transient Thermomechanical Behavior of SiMo Ductile Iron by Al Alloying