Abstract:Electrical characterization of semiconducting oxide nanowires (NWs) is mostly performed using complex techniques, which necessitates a series of costly nanofabrication procedures. In this work, with the aim to provide a low-cost, feasible, facile, and reproducible approach for enabling the study of NW electrical properties, we report direct electrical measurements on individual and overlapped suspended zinc oxide NWs (ZnO NWs). We have succeeded in constructing both two- and three-terminal devices simply by employing tungsten (W) nanoprobes with the aid of a nanomanipulation system embedded inside a scanning electron microscope’s vacuum chamber. Stable contacts were established using the Joule heating effect and e-beam exposure at the junctions between the NW and the pre-cleaned W tips. P-channel field-effect transistor devices were achieved with an on–off current ratio of ∼101, a threshold voltage (>1.5 V), a transconductance of ∼16 μS, a sub-threshold swing of ∼220 mV/decade, and field-effect carrier mobility roughly estimated to be around 926.4 cm2/(V·s) after correction for contact resistances/optimization. The average resistivity of ZnO NWs was calculated to be ∼2.23 × 10–2 Ω·cm for NWs with diameters between 70 and 500 nm. Besides, we have demonstrated a contact resistance of ∼19.60 kΩ and a Schottky barrier height of ∼0.37 eV present at W/ZnO NW interfaces. The contact resistance between two overlapped ZnO NWs was estimated to be ∼283 kΩ, which is relatively higher than that offered between W/ZnO NWs. This work provides a solid experimental procedure to address true intrinsic electrical properties at metal/semiconductor interfaces, and our findings have potential applications in next-generation 3D suspended ZnO NW-based nanoelectronic devices.

Fabrication of ZnO Nanowire Devices Via Selective Electrodeposition

Fabrication of ZnO/Al2O3 core–shell nanostructures and crystalline Al2O3 nanotube

A General Approach For Fabricating Arc-Shaped Composite Nanowire Arrays By Pulsed Laser Deposition

Arrays of ZnO Nanowires Fabricated by a Simple Chemical Solution Route

Pinning of Single-Walled Carbon Nanotubes by Selective Electrodeposition

A General Approach for Fabricating Arc‐Shaped Composite Nanowire Arrays by Pulsed Laser Deposition

Characterization of Electrical Properties of Suspended ZnO Nanowires Using a Nanorobotic Manipulation System Inside a Scanning Electron Microscope for Nanoelectronic Applications

Electrochemical Synthesis of Copper Nanowires

Fabrication of Metal Nanoelectrodes by Interfacial Reactions

Electrochemical fabrication and structure of Ni<sub><i>x</i></sub>Zn<sub>1−<i>x</i></sub> alloy nanowires

Controlled Synthesis of Oriented Single-Crystal Zno Nanotube Arrays on Transparent Conductive Substrates

Controllably Constructing Gold Nanostructures on Electrodes Through Growth of Zinc Oxide Nanorods and Two-Step Electroplating

Fabrication of A Nano-Scale Gap by Selective Chemical Deposition

Electric-field-assisted growth and alignment of ZnO nanowires in device fabrication

Controllable fabrication of various ZnO micro/nanostructures from a wire-like Zn–EG–AC precursor via a facile solution-based route

Synthesizing Cu-Sn nanowires alloy in highly-ordered Aluminum Oxide templates by using electrodeposition method

Realization and characterization of nano electromechanical devices based on ZnO nanowires

The Effect of the Solution Flow and Electrical Field on the Homogeneity of Large-Scale Electrodeposited ZnO Nanorods

Fabrication of ZnO Nanowires by Vapor-Phase Deposition and Their Field Emission Properties

Mechanism of the Electrodeposition of ZnO Nanosheets below Room Temperature

Direct electroplating of Ag nanowires using superionic conductors