Abstract:Functional gradient materials (FGM), with their composition gradually varied in different positions, have attracted much attention for research and development during the years. Normally there are two types of functional gradient materials: one without the formation of intermetallics which is easier for fabrication due to less scientific and technological challenge; the other one with the formation of intermetallics in some part of the gradient changed composition range such as Ti-Al, Ti-Fe, Ni-Al gradient materials, which still exists big challenge on intermetallic, resulting in high brittleness and unavailability.Laser deposition is a competitive candidate for FGM due to its capability on accurate composition and precise dimension control. According to an aeronautical application requirement to gradually change the composition from Ti6Al4V to 316L, this paper reports on laser deposition of Ti6Al4V to 316L gradient composition structure. A big challenge is the formation of the TiFe intermetallic especially near the composition of Ti50Fe50, which results in very high cracking tendency. Many efforts have been made to optimize the Ti-Fe composition ratio, the deposition process and the deposition parameters, not a single Ti6Al4V-316L composition gradient structure was successful due to the formation of the very brittle TiFe and TiFe2 intermetallics. This indicates that it is almost impossible to direct deposit Ti6Al4V to 316L without cracking and separation. We used Inconel 625 powder as an interlayer between the Ti6Al4V and the 316L, thus a sound Ti6Al4V-316L composition gradient structure was successfully achieved by laser deposition. The brittle TiFe and TiFe2 intermetallics were replaced by a series of phase evolutions: α+β → β+Ti2Ni→Ti2Ni+TiNi→TiNi→TiNi+TiNi3→Ni3Fe→ Ni2Fe3→γFe. The brittleness was dramatically decreased or diluted and crack-free composition gradient structure was available. The gradient structure was further analyzed on hardness, microstructural evolution, the Young's modulus and Poisson's ratio.

Microstructure and Mechanical Property of Laser Melting Deposition (lmd) Ti/Tial Structural Gradient Material

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Microstructure Evolution of TC25G/Ti2AlNb Structural Gradient Material Fabricated by Laser Directed Energy Deposition

Microstructure and mechanical properties of laser melting deposited γ-TiAl intermetallic alloys

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Microstructure and Properties of Ti/Al Lightweight Graded Material by Direct Laser Deposition

Laser Deposition of Ti6Al4V-316L Composition Gradient Structure: Challenge on Intermetallics

Laser deposition of graded -TiAliTi<sub>2</sub>AlNb alloys: Microstructure and nanomechanical characterization of the transition zone

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

Chemical, microstructure, and mechanical property of TiAl alloys produced by high-power direct laser deposition

Microstructure And Tensile Properties Of Laser Melting Deposited Ti-5al-5mo-5v-1cr-1fe Near Beta Titanium Alloy

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Microstructural evolution and mechanical properties of laser melting deposited Ti–6.5Al–3.5Mo–1.5Zr–0.3Si titanium alloy

Microstructure and mechanical properties of Ti60–Ti 2 AlNb functionally graded materials fabricated by laser directed energy deposition

Microstructure and mechanical behavior of commercial purity Ti/Ti-6Al-2Zr-1Mo-1V structurally graded material fabricated by laser additive manufacturing

Compositional Variation and Microstructural Evolution in Laser Additive Manufactured Ti/Ti–6Al–2Zr–1Mo–1V Graded Structural Material

The Microstructure and Mechanical Behaviors of the Ti–6.5Al–3.5Mo–1.5Zr–0.3Si Alloy Produced by Laser Melting Deposition

Compositional Changes and Microstructure Evolution of Ti6Al4V-Inconel718 Functionally Graded Materials by Laser Additive Manufacturing

Study of microstructure and compressive strength of a novel Ti-0.75Al-9.5V alloys manufactured by laser deposition melting

The effects of heat treatment on the microstructure and mechanical property of laser melting deposition γ-TiAl intermetallic alloys

Microstructure evolution and mechanical properties of TiB/Ti6Al4V gradient-material lattice structure fabricated by laser powder bed fusion