Abstract:In order to gain insight into the influence of grain size on precipitation thermodynamics, bulk materials of coarse-grained (CG), ultrafine-grained (UFG) (with or without dislocations), and nanocrystalline (NC) 7075 Al alloy have been fabricated by solid solution treatment, equal-channel angular pressing (ECAP), or high-pressure torsion (HPT) processes. The precipitation behavior and the corresponding thermal phenomenon were studied by transmission electron microscopy (TEM) and differential scanning calorimetry (DSC) heating. The results indicated that there are significant differences in precipitation thermodynamics among the four bulk materials. In the CG and UFG materials without dislocations, homogeneous nucleation is the primary precipitation mechanism. However, the nucleation of the GP zones is suppressed at lower temperatures due to a reduction in the number of residual vacancies and the supersaturation in the UFG interiors. This is attributed to the absorption of vacancies and solute atoms by a greater volume of grain boundaries. It can be observed that the greater the excess of vacancies remaining in grain interiors, the lower the temperature at which nucleation of GP zones occurs. Defect-assisted heterogeneous nucleation was identified as the predominant precipitation mechanism in the UFG materials with dislocations and the NC materials. These defects encompass dislocations, lattice distortions, and grain boundaries. The decomposition processes of solid solutions were found to be almost complete at a lower temperature. The presence of dislocations, lattice distortions, and grain boundaries enables solute atoms to diffuse at a much faster rate, significantly enhancing the precipitation rate and reducing the nucleation and formation energies of various precipitate phases.

Discontinuous Precipitation Initiated At Interphase Boundaries In A Zn-Rich Zn-6.3 At.% Ag Alloy

Initiation of Discontinuous Precipitation at Interphase Boundaries in a Two-Phase Zn–6.3 At.% Ag Alloy

Evolution of Precipitate and Precipitate/matrix Interface in Al-Zn-Mg-Cu(-Ag)alloys

Atomic-scale study on the precipitation behavior of an Al-Zn-Mg-Cu alloy during isochronal aging

COMPUTER SIMULATION FOR PRECIPITATION PROCESSO Ni_<75>Al_<2.5>V_<22.5> ALLOY WITH THE MICROSCOPIC PHASE-FIELD METHOD

Atomic-scale computer simulation of mixture precipitation mechanism for Ni75AlxV25-x alloy

Precipitation Thermodynamics in an Al–Zn–Mg Alloy with Different Grain Sizes

Effect of Grain Boundary Precipitation on Elastic Properties of Cu-2.0%Be Alloy

Precipitation Sequence of Middle Al Concentration Alloy Using the Inversion Algorithm and Microscopic Phase Field Model

Segregation assisted grain boundary precipitation in a model Al-Zn-Mg-Cu alloy

Differential effects of Fe, Ti and Fe + Ti addition on the discontinuous precipitation and properties of cu-Ni-Sn alloys

On the Precipitation in an Ag-Containing Mg-Gd-Zr Alloy

Preferential Growth of Coherent Precipitates at Grain Boundary

Electron Microscopic Study of Precipitate Free Zones along Grain Boundaries in the Mg96.9Gd2.8Nd0.3 Alloy

Kinetics of Cellular Discontinuous Precipitation in A Re-Containing Single Crystal Superalloy

Atomic-scale investigation of the heterogeneous precipitation in the E (Al18Mg3Cr2) dispersoid of 7075 aluminum alloy

Investigation of the Interface Precipitation on Α-Al(fe,mn)si Particles in Al–Fe–Mn–Si–Mg–Cu Alloy

The Effect of Discontinuous Γ' Precipitation on the Mechanical Properties of Al-Co-Ni Alloys

The dependence of precipitate morphology on the grain boundary types in an aged Al–Cu binary alloy

Revisiting the precipitation mechanisms of Guinier-Preston zones, η′, and η precipitates in Al-Zn-Mg alloys

Precipitation in an Al-Zn-Mg-Cu alloy during isothermal aging: Atomic-scale HAADF-STEM investigation