Abstract:This paper reports a high-speed packaging for Silicon Mach-Zehnder modulators (MZMs). The radio frequency (RF) input port of the package is commercially available GPPO type. High-frequency ceramic substrate is designed to shorten the length of gold wire to suppress the RF attenuation. Gratings and single-mode fibers using inclined-surface coupling are used to realize low-loss and large tolerance coupling. In measurement, clear eye diagrams with ER of 10.1 dB and 7.6 dB were obtained at 25 Gb/s and 40 Gb/s modulations. Silicon photonics has become a hot research topic in the field of optoelectronics in recent years, since silicon–based optical device can achieve high density integration, low power consumption, low cost photonic devices, realize monolithic integration with electronic devices, and it is compatible with traditional CMOS processes [1]. Silicon electro-optic modulators which are key devices in optoelectronic information transmission and processing have got great developments in recent years. High speed OOK silicon modulators have been demonstrated [2-4]. The silicon modulator packaging has also been studied [5-6]. However, the operating speed of packaged silicon modulators still need to be improved. Our butterfly package for silicon modulator is illustrated in Figure 1. Two main designs were applied for high speed packaging: the modulator chip was designed with reverse PN mode, whose PN junction capacitance is smaller and the modulator electrode was carefully designed using CPW travelling-wave electrodes; GCPW transmission lines with metallic holes were adopted to fabricate the high-frequency ceramic substrates to make the high-speed electrical signal effective loading on the electrode of the MZM chip. Since micro-strip-like line (MSL) mode in GCPW line might exist, which usually cause energy coupling of CPW mode and prompt a microwave resonant of transmission response in high frequency range [7], we made metallic holes on a transmission line to suppress the microwave resonant [8-9]. Grating coupler and single-mode fiber with inclined-surface are used in optical coupling. The advantages of this optical coupling method is larger misalignment tolerance and cheap cleaved fiber packaging. Nickel metal tube is installed close to the inclined-surface of single-mode fiber, the position and angle of the optical fiber is adjusted by special fixture clamping nickel metal tube and adjusting the special fixture. Assuming the optical fiber is parallel to the chip surface, there is a relation of θ=2*φ-90o. We choose the φ=51 deg. as our grating incidence angle is 12 degree. Eye-diagram measurements were carried to demonstrate the high-speed operation of the packaged modules. Experimental results were presented in Fig. 4(a) and 4(b). Clear eye diagrams with ERs of 10.1 dB and 7.6 dB were obtained at 25 Gb/s and 40 Gb/s modulation speed. By improving the welding between the pin of GPPO connector and ceramic substrates, further reducing the length of gold wires from the ceramic substrates to the modulator pads, the speed of the packaged MZM module could be higher.

High-Speed Coplanar Waveguide Based Submount for 40 Gbit/s Electroabsorption Modulator

Bing Xiong, Jianbo Tian, Jian Wang, Pengfei Cai, Changzheng Sun

HIGH-SPEED Al2O3 -BASED SUBMOUNT FOR 40Gb/s ELECTROABSORPTION MODULATORS

Novel Low-Cost Wideband Si-Based Submount for 40 Gb/S Optoelectronic Devices

Design and fabrication of heat sink with impedance matching circuit for high-speed EA modulators

Novel Planar Electrode Structure for High-Speed (>40 GHz) Electroabsorption Modulators

High-speed (10-40 Gb/s) Electroabsorption Modulator Integrated Devices for Fiber Communications

30GHz Ge electro-absorption modulator integrated with 3 μm silicon-on-insulator waveguide

Resonance Suppression of Grounded Coplanar Waveguide in Submount for 40 Gb/s Optoelectronic Modules

A Wideband Electro-Optic Modulator Based on Long Range Surface Plasmon Resonances

High Speed Electro-Absorption Modulators for Digital and Analog Optical Fiber Communications

High-speed packaging for silicon modulator

High-speed (>40 GHz) Integrated Electroabsorption Modulator Based on Identical Epitaxial Layer Approach

High speed GeSi electro-absorption modulator at 1550 nm wavelength on SOI waveguide

High-speed Silicon Modulators for the 2 Μm Wavelength Band

Compact 100gbaud Driverless Thin-Film Lithium Niobate Modulator on a Silicon Substrate

Gain-Coupled 4×56 Gb/s EML Array with Optimized Bonding-Wire Inductance

Low-threshold DFB-laser-integrated High-Speed EA Modulators Based on Ridge Waveguide Structure by ICP Etching

Study on 40 GHz coplanar waveguide polymer electro-optic modulators

Electro-Optic Silicon Modulator With Horizontal Photonic Crystal Slot Slab

40 Gb/S Algainas Electroabsorption Modulated Laser Module Based on Identical Epitaxial Layer Scheme