Abstract:Crystallographic textures and their effect on the mechanical anisotropy of a hot-rolled biomedical Co-Cr-Mo alloy were investigated. The hot-rolled Co-28Cr-6Mo-0.13N (mass%) alloy examined here exhibited a monotonic strength increment following hot-rolling reduction, eventually reaching a 0.2% proof stress of 1400 MPa while maintaining acceptable ductility (>10%). The dominant hot-rolling texture was a brass-type component, which is characterized by the alloy's peculiarly low stacking fault energy (SFE) even at hot rolling temperatures, although the minor peaks of the near copper component were also identified. However, because of the onset of dynamic recrystallization (DRX) during the hot rolling process, the texture intensity was relatively weak even after 90% hot rolling, although the grain refinement originating from the DRX was not significant (the "less active DRX" condition increased the strain accumulation during the process, resulting in high-strength samples). The weakened texture development resulted in negligible in-plane anisotropy for the hot-rolled specimen strength, when the specimens were tensile strained in the rolling direction (RD) and transverse direction (TD). The elongation-to-failure, however, exhibited a difference with respect to the tensile loading axis. It is suggested that the ductility anisotropy is closely related to a strain-induced γ (fcc) → ε (hcp) martensitic transformation during tensile loading, resulting in a difference in the proportion of quasi-cleavage fracture surfaces. The obtained results will be helpful in the development of high-strength Co-Cr-Mo alloy plates and sheets, and have implications regarding plastic deformation and texture evolution during the hot rolling of non-conventional metallic materials with low SFE at elevated temperatures, where planar dislocation slips of Shockley partial dislocations and thermally activated process interplay.

Experimental Investigation and Simulation of the Texture Evolution During Rolling Deformation of an Intermetallic Fe-28 At.% A1–2 At.% Cr Polycrystal at Elevated Temperatures

Texture Evolution of Polycrystalline Aluminum During Rolling Deformation Ii. Theoretical Simulation

Experiments and Crystal Plasticity Finite Element Simulations of Texture Development during Cold Rolling in a Ti-15V-3Cr-3Sn-3Al Alloy

Texture Evolution in an Al-Cu-Mg Alloy During Hot Rolling

TEXTURE EVOLUTION OF POLYCRYSTALLINE ALUMINUM DURING ROLLING DEFORMATION I.Experimental Study

Local Texture Evolution during Rolling Deformation of Single Crystals of {100} Orientation

Rolling texture development in a dual-phase Mg-Li alloy: The role of temperature

Crystal Plasticity Finite Element Simulation of Grain Evolution Behavior in Aluminum Alloy Rolling

Texture Evolution and Dynamic Recrystallization of Zr–1Sn–0.3Nb–0.3Fe–0.1Cr Alloy During Hot Rolling

Evolutions of Microstructure and Crystallographic Texture in an Fe-1.2 wt.% Si Alloy After (A)Symmetric Warm Rolling and Annealing

A crystal plasticity FEM study of through-thickness deformation and texture in a {112} <111> aluminium single crystal during accumulative roll-bonding

Evolution of Micro-Textures Within Individual Grains in Rolled Polycrystal Aluminum

Texture evolution and mechanical anisotropy of biomedical hot-rolled Co-Cr-Mo alloy

Texture Evolution and the Recrystallization Behavior in a Near Β Titanium Alloy Ti-7333 During the Hot-Rolling Process

Texture Evolution and Dynamic Recrystallization in a Beta Titanium Alloy During Hot-Rolling Process

Texture Stability and Transition in an Accumulative Roll-Bonding-Processed Aluminum Single Crystal

Microstructure and Crystallographic Texture of Rolled Polycrystalline Fe 3 Al

Texture and mechanical properties of warm rolled Fe3Al alloy

Effect of Heterophase Interfaces on Microstructure and Crystallographic Texture Evolution During Rolling of Directionally Solidified Ag-Cu Eutectic Alloy

Recrystallization Texture Evolution of Cold-Rolled Cu Foils Governed by Microstructural and Sample Geometrical Factors During Heating

Deformation Mechanism of Cold Ring Rolling in View of Texture Evolution Predicted by a Newly Proposed Polycrystal Plasticity Model