Abstract:Crystallographic textures and their effect on the mechanical anisotropy of a hot-rolled biomedical Co-Cr-Mo alloy were investigated. The hot-rolled Co-28Cr-6Mo-0.13N (mass%) alloy examined here exhibited a monotonic strength increment following hot-rolling reduction, eventually reaching a 0.2% proof stress of 1400 MPa while maintaining acceptable ductility (>10%). The dominant hot-rolling texture was a brass-type component, which is characterized by the alloy's peculiarly low stacking fault energy (SFE) even at hot rolling temperatures, although the minor peaks of the near copper component were also identified. However, because of the onset of dynamic recrystallization (DRX) during the hot rolling process, the texture intensity was relatively weak even after 90% hot rolling, although the grain refinement originating from the DRX was not significant (the "less active DRX" condition increased the strain accumulation during the process, resulting in high-strength samples). The weakened texture development resulted in negligible in-plane anisotropy for the hot-rolled specimen strength, when the specimens were tensile strained in the rolling direction (RD) and transverse direction (TD). The elongation-to-failure, however, exhibited a difference with respect to the tensile loading axis. It is suggested that the ductility anisotropy is closely related to a strain-induced γ (fcc) → ε (hcp) martensitic transformation during tensile loading, resulting in a difference in the proportion of quasi-cleavage fracture surfaces. The obtained results will be helpful in the development of high-strength Co-Cr-Mo alloy plates and sheets, and have implications regarding plastic deformation and texture evolution during the hot rolling of non-conventional metallic materials with low SFE at elevated temperatures, where planar dislocation slips of Shockley partial dislocations and thermally activated process interplay.

Origin of the {111}〈112〉 Cold Rolling Texture Development in a Soft Magnetic Fe-27%Co Alloy

A comprehensive study on texture evolution and recrystallization mechanism of Fe-4.5 wt% Si with strong {114}

Texture evolution in grain-oriented electrical steel during hot band annealing and cold rolling

Texture Evolution and Plastic Deformation Mechanism of Cold-Drawn Co-Cr-Ni-Mo Alloy

Effect of Slab Reheating Temperature on Cold Rolling Texture Evolution of Nb-Containing Grain-Oriented Silicon Steel

Texture evolution and mechanical anisotropy of biomedical hot-rolled Co-Cr-Mo alloy

Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing

Understanding the Mechanisms of Texture Evolution of a Fe-24Cr-22Ni-7Mo Super Austenitic Stainless Steel During cold Rolling and Annealing

Secondary recrystallization induced by composite precipitates in magnetostrictive Fe-Ga alloy thin sheet

In-situ observations of static recrystallization and texture formation in a cold-rolled CoCrFeMnNi high entropy alloy

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Evolutions of Microstructure and Crystallographic Texture in an Fe-1.2 wt.% Si Alloy After (A)Symmetric Warm Rolling and Annealing

The role of Goss-oriented texture for brass-type texture in nickel-based metals during cold rolling

Dislocation Strengthening and Texture Evolution of Non-Oriented Fe-3.3 wt% Si Steel in Double Cold Rolling

The origin of {113} grains and their impact on secondary recrystallization in producing ultra-thin grain-oriented electrical steel

Rolling texture development in a dual-phase Mg-Li alloy: The role of temperature

Texture Evolution during Recrystallization and Grain Growth in Non-Oriented Electrical Steel Produced by Compact Strip Production Process

Texture evolution and slip mode of a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr dual-phase alloy during cold rolling based on multiscale crystal plasticity finite element model

Improvement of magnetic permeability in pure iron sheets

The effect of grain size before cold rolling on the magnetic properties of thin-gauge non-oriented electrical steel

Rapid Secondary Recrystallization of the Goss Texture in Fe81Ga19 Sheets Using Nanosized NbC Particles