Abstract:A TD-split basal texture with two peaks highly tilted from the normal direction (ND) towards the transverse direction (TD) is usually developed in Mg-Zn-Ca plates and can effectively improve ductility and formability. In the present study, the texture evolution during cold rolling and subsequent annealing of a Mg-2Zn-1Ca plate with initial TD-split texture was investigated, and new insights into the mechanisms of texture evolution were obtained. The results show that a dumbbell-shaped basal texture transformed into an elliptical shape after 41% cold rolling. The random distribution of prismatic planes became preferred with largely parallel to the rolling direction (RD). Crystal plasticity simulations revealed that basal slip was the predominant deformation mode, and inclined basal poles toward the ND. The activation of other non-basal slips would retard this tendency. Prismatic slip with a relative activity of 20% to 30% preserved the pre-existing TD-split texture after a high rolling reduction of 41%. Pyramidal slip prevented the formation of basal fiber and lead to a spreading of basal poles toward the RD mainly at strains over 29%. After full recrystallization, the elliptical TD-split basal texture became a dumbbell-shaped TD-split texture. Grain nucleation was observed at grain boundaries (GBN mechanism), within deformation twins (DTN mechanism), and near precipitates (PSN mechanism). GBN and DTN mainly developed a TD-split basal-texture. Instead of the formation of random orientations as considered previously, PSN produced a TD-split basal-texture, and the basal poles exhibited a much wider distribution with high angle of the peaks off the ND. The grains nucleated by GBN, DTN, and PSN did not exhibit preferred growth, and consequently, the texture hardly changed during subsequent grain growth.

The role of Goss-oriented texture for brass-type texture in nickel-based metals during cold rolling

Micro-mechanical aspects of texture evolution in nickel and nickel–cobalt alloys: role of stacking fault energy

Microstructure Evolution and Texture Characteristics of Pure Nickel N6 During Cold Rolling Process

Understanding the Mechanisms of Texture Evolution of a Fe-24Cr-22Ni-7Mo Super Austenitic Stainless Steel During cold Rolling and Annealing

Investigation on Grain Size Effect of Rolling Texture in Copper

Origin of the {111}〈112〉 Cold Rolling Texture Development in a Soft Magnetic Fe-27%Co Alloy

Texture and Deformation Structure Evolution During Rolling of Individual Grains of Columnar Grain Nickel

Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing

Microstructure and Texture Evolution in Cold-Rolled and Annealed Oxygen-Free Copper Sheets

Analysis of Through-Thickness Heterogeneities of Microstructure and Texture in Nickel after Accumulative Roll Bonding

Orientation relationship of texture development in hot-rolled W during annealing

Investigation of the Microstructure and Rolling Texture Evolution of Cu-45 At.% Ni Alloys During the Recovery Process by Quasi-In Situ Electron Backscatter Diffraction

Effect of cross cold rolling and annealing on microstructure and texture in pure nickel

Recrystallization Texture Evolution of Cold-Rolled Cu Foils Governed by Microstructural and Sample Geometrical Factors During Heating

Systematical Analysis on the Grain Orientation Evolution of Pure Nickel under Plastic Deformation by Using In-Situ EBSD

Effect of stress-relief annealing on rolled texture of nickel-based alloys

Microstructure, Texture, and Deep Drawability under Two Different Cold-Rolling Processes in Ferritic Stainless Steel

Evolution of Microstructure, Texture and Topography During Cold Rolling and Recrystallization of Ni–5at.%W Alloy Substrate for Coated Conductors

Effect of cryogenic rolling on the microstructure and texture of CuCrZr alloy

Microstructure and Texture Evolution of Cu-Ni-P Alloy after Cold Rolling and Annealing

An Investigation on Rolling Texture Transition in Copper Preprocessed by Equal Channel Angular Pressing