Abstract:Nanocomposite Ti-Al-Si-N films (Al content ranging from 0 to 16.7 at.% and Si from 0 to 11.8 at.%, respectively) were prepared on Si(100) substrates at 500'C by reactive close-field unbalanced magnetron sputtering in an Ar-N, mixture. The chemical composition, bonding structure, surface morphology, microstructure, stress and mechanical properties of these films were systematically investigated by means of energy dispersive spectrometry (EDS), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), X-ray diffraction (XRD), optical interference system and nanoindentation measurements.The XPS measurements reveal evolution of chemical composition and bonding structure of the deposited Ti-Al-Si-N films. The observed nonlinear peak shift of Ti 2p and N 1s indicates the bonding evolution of crystalline TiN. The spectra from Al 2p at 73.7 eV and Si 2p at 101.1 eV indicates the evolution of film composition from TiSiN to TiAlN with the incorporation of Al, and also implies that their chemical states are mainly in the form of SiNx and AlN, respectively. The (1 1 1) diffraction peak from the XRD theta-2 theta patterns shows a variation either on peak width or on peak position, indicating the variation of grain size and lattice constant. The calculated lattice constant reveals a mixture of different phases whose structures are similar to TiN. The nonlinear variation of grain size and lattice constant is considered due to the competition between two processes, i.e. Al addition and the underlying Si reduction. In order to further understand the microstructure evolution, the XRD spectra and corresponding calculations of the Ti-Al-Si-N films without heating during deposition are also shown for comparison. The effect of substrate heating is discussed. The present results show that the influence of Si and Al addition on the grain growth is different.The surface roughness of Ti-Al-Si-N films also exhibits a nonlinear variation, which is due to the variation of grain size and the competitive growth of different phases. The influence of stress on the hardness can be ignored due to its relatively low value (1-2 GPa) compared with the super-hardness of the films. All the quaternary Ti-Al-Si-N films show enhanced mechanical properties when compared with the nanocomposite Ti-Si-N and Ti-Al-N films deposited under the same condition. The best hardness, reaching superhard, is obtained for the Ti-AI-Si-N film with 7.5 at.% Al and 6 at.% Si. The combined effect of vacancy hardening and some of extrinsic hardening are considered responsible for the enhanced mechanical properties of Ti-Al-Si-N films. (c) 2006 Elsevier B.V. All rights reserved.

Crystal Orientation And Hardness Of Au/Nicr/Ta Films On Si-(111) Substrate Prepared By Magnetron Sputtering

The Mechanical Properties and Resistivity of Au/NiCr/Ta Multi-Layered Films on Si-(111) Substrate

Characterization of the surface roughness and nanoindentation hardness of Au/NiCr/Ta multilayers

CHARACTERIZATION OF THE SURFACE ROUGHNESSAND NANOINDENTATION HARDNESS OFAu/NiCr/Ta MULTILAYERS

Hardness and Elastic Modulus of Au/NiCr/Ta Multilayers on Al2O3 Substrate by Nanoindentation Continuous Stiffness Measurement Technique

Surface Roughness and Resistivity of Au Film on Si-(111) Substrate

Surface Morphology, Crystal Orientation and Scratch Properties of Au/Nicr/Ta Multi-Layered Metallic Films

Residual stress and crystal orientation in magnetron sputtering Au films

The Relationship Between Residual Stress and Resistivity of Au/Nicr/Ta Multi-Layered Metallic Films by Magnetron Sputtering

Microstructure and Electrical Characteristics of Cr–Si–Ni Films Deposited on Glass and Si (100) Substrates by RF Magnetron Sputtering

The Relationship Between Preferred Orientation and Stress in Multilayered Au/Nicr/Ta Films

Nitride Films Deposited from an Equimolar Al–Cr–Mo–Si–Ti Alloy Target by Reactive Direct Current Magnetron Sputtering

X-ray Diffraction Measurement of Residual Stress and Crystal Orientation in Au/NiCr/Ta Films Prepared by Plating

Superhard Nanocomposite Ti–Al–Si–N Films Deposited by Reactive Unbalanced Magnetron Sputtering

Hard Nanocomposite Ti–Si–N Films Prepared by DC Reactive Magnetron Sputtering Using Ti–Si Mosaic Target

Structure, Composition and Mechanical Properties of Reactively Sputtered (tivcrtaw)nx High-Entropy Films

Investigation of deposition parameters on the structural properties and hardness of TiAlN films deposited via reactive pulsed DC magnetron sputteringInvestigation of deposition parameters on structural properties and hardness of TiAlN films deposited by reactive pulsed DC magnetron sputtering

Microstructure and Mechanical Properties of Co-Deposited Ti-Ni Films Prepared by Magnetron Sputtering

Structural and Mechanical Properties of Multi-Element (alcrmotatizr)nx Coatings by Reactive Magnetron Sputtering

The Mechanism of Super Hardness of Nanocrystallite TiN Films Deposited by Pulsed D.c. Bias Multi-Arc Ion Plating

Structure and Properties of Two Al–Cr–Nb–Si–Ti High-Entropy Nitride Coatings