Abstract:The microstructure, mechanical performance, and tribological properties of SiC ceramic coatings prepared via atmospheric plasma spraying (APS) and chemical vapor deposition (CVD) method were compared to provide good anti-wear protection for carbon/carbon composites. The surface morphology of the APS-SiC coating was characterized as having a porous structure, whilst the CVD-SiC coating presented with many pyramidal-shaped crystals constituting the surface. The APS-SiC coating consists of a dominating SiC phase and a small fraction of the Si phase, while the XRD pattern of the CVD-SiC coating mainly consists of the SiC phase. The dense crystalline microstructure of the CVD-SiC coating made it possess a higher hardness and Young's modulus at 31.0 GPa and 275 GPa, respectively. The higher H/E and H3/E2 parameters of the CVD-SiC coating implied that it exhibited better plastic resistance, which is also beneficial for anti-wear properties. The scratch test reflected the critical loads of the spallation of the APS-SiC coating and CVD-SiC coating, which were evaluated to be 25.9 N and 36.4 N, respectively. In the tribological test, the friction coefficient of the APS-SiC coating showed obvious fluctuations at high load due to damage to the SiC coating. The wear mechanism of the APS-SiC coating was dominated by abrasive wear and fatigue wear, while CVD-SiC was mainly dominated by abrasive wear. The wear rate of the CVD-SiC coating was far below that of the APS-SiC coating, suggesting the better wear-resistance of the CVD-SiC coating.

Comparison Between Wear Resistance of Subsonic Speed Flame Spraying Coating and Plasma Spraying Coating

Wear performance of the plasma sprayed fine WC-Co composite powders coatings

Effect of Nanometer WC Powder on Wear Resistance of Thermal Spraying Coating

Research Status of Plasma-sprayed Ceramic Wear-resistance Coating

Characterization of Supersonic Plasma Sprayed WC-12Co Coatings

Influence of WC Content on Wear Resistance of Spraying-Welding Co/WC Coatings

Study on Properties of Coatings Prepared by Supersonic Plasma Spraying with Three Kinds of WC-12Co Powder

Tribological Behavior of Various Plasma-Sprayed Ceramic Coatings

Comparison of the tribological properties of an ion sulfurized coating and a plasma sprayed FeS coating

Study on Wear Performance of Rare-earth Modified WC/12Co Thermally Sprayed Coatings

Microstructure and wear behavior of FeCoNiCrMn high entropy alloy coating deposited by plasma spraying

Comparison on multi-angle erosion behavior and mechanism of Cr3C2-NiCr coatings sprayed by SPS and HVOF

Wear Behavior of Plasma Sprayed Ni-WC Composite Coatings

Study on Friction and Wear Performance of NiCrBSi-Mo and QSn-Ni/C Coatings Friction Paris

Erosion Resistance of Cermet Coatings Deposited by Supersonic Atmospheric Plasma Spraying

Effect of Plasma Sprayed Ceramic and Cermet Coatings on Wear-Out Failure of High Temperature Ball Valve

Effect of Flame Conditions on Abrasive Wear Performance of Hvof Sprayed Nanostructured Wc-12co Coatings

A Comparison of the Tribological Properties of SiC Coatings Prepared via Atmospheric Plasma Spraying and Chemical Vapor Deposition for Carbon/Carbon Composites

Microstructure, formation mechanism and properties of plasma-sprayed Cr7C3—CrSi2—Al2O3 coatings

Effects of post-coating processing on structure and erosive wear characteristics of flame and plasma spray coatings

Comparison of the Mechanical and Electrochemical Properties of WC-25Co Coatings Obtained by High Velocity Oxy-Fuel and Cold Gas Spraying