Abstract:This work studies the effect of mechanical properties and microstructure on sliding wear and cavitation erosion behaviors of cermet coatings deposited via high velocity oxy-fuel (HVOF) spraying on AZ31 magnesium substrate. Cavitation tests indicated that WC-Co-Cr cermet had superior resistance to cavitation erosion than WC-Cr 3 C 2 -Ni, WC-Co coatings, and far better resistance than the AZ31 expressed by the volume material loss 3.74 mm 3 , 6.99 mm 3 , 10.30 mm 3 , and 108.82 mm 3 , respectively. WC-Co-Cr coating's erosion mechanism exhibited uniform material removal, which slows the erosion rate. The CoCr binder prevented severe surface pitting and the detachment of the WC-Co-Cr cermet material in massive chunks which was observed for WC-Co and WC-Cr 3 C 2 -Ni coatings. Cermet coatings microstructure discontinuities such as pores and ceramic-metallic phase interfaces are the centers of material erosion. No clear correlation between the erosion behavior and mechanical properties of coatings was revealed. Contrary to that, sliding wear results were strongly related to the mechanical properties. The WC-Co-Cr and WC-Co samples exhibited higher hardness and higher values of Young's modulus than the WC-Cr 3 C 2 -Ni one. The generated stresses with lower values of hardness and Young's modulus for the WC-Cr 3 C 2 -Ni sample resulted in a higher wear factor, approx. 1·10 −7 mm 3 ·N −1 ·m −1 . For the harder samples, which exhibited higher stiffness (WC-Co-Cr and WC-Co), this type of wear resulted in lower values of the wear factor: 6·10 −8 mm 3 ·N −1 ·m −1 and 9·10 −8 mm 3 ·N −1 ·m −1 , respectively. Deposition of the cermet coatings effectively protected the magnesium substrate, which shows low resistance to cavitation erosion and sliding wear when uncoated.

Erosion Resistance of Cermet Coatings Deposited by Supersonic Atmospheric Plasma Spraying

Erosion Resistance Of Ni-Wc Self-Fluxing Alloy Coating At High Temperature

Cavitation erosion resistance of WC-Cr-Co and Cr3C 2-NiCr coatings prepared by HVOF

Effect of Nitrogen Protective Atmosphere on Microstructure and High Temperature Erosion Property of TiAl3 and Cr3C2 Composite Coatings

Comparison on multi-angle erosion behavior and mechanism of Cr3C2-NiCr coatings sprayed by SPS and HVOF

Microstructure and mechanical property of high velocity oxy-fuel sprayed multimodal WC-Cr3C2–Co–Y2O3 cermet coating

Erosion–corrosion Resistance of Microcrystalline and Near-Nanocrystalline WC–17Co High Velocity Oxy-Fuel Thermal Spray Coatings

Study on High-temperature Erosion Resistance of NiCoCrAlY/ZrO2 Thermal Barrier Coating

Resistance of HVOF-Sprayed Cr3C2-25NiCr and WC-10CO-4Cr coatings to cavitation and erosion by mud jetting

Investigations of cavitation erosion and wear resistance of cermet coatings manufactured by HVOF spraying

Microstructure and Ablation Behavior of W Coating Prepared by Atmospheric Plasma Spraying for Zr/Cu Infiltrated C/C Composites

Microstructure and Wear Performance of WC Reinforced Ni-based Composite Coating

Tribological characteristics of WC-Cr3C2-Ni cermet coatings under different wear parameters

Microstructure and abrasive resistance of ZrO2-MoSi2 coatings deposited by supersonic plasma spraying

Ablation Resistance of C/C Composites with Atmospheric Plasma-Sprayed W Coating

Abrasive Resistance of Arc Sprayed Coatings with a WC Ceramic Phase

Corrosion Resistance Enhancement of WC Cermet Coating by Carbides Alloying

Supersonic flame ablation resistance of W/ZrC coating deposited on C/SiC composites by atmosphere plasma spraying

Preparation and High Temperature Erosion Resistance of Cr3C2-NiCr Coating

High-temperature erosion behavior of high-velocity arc-spraying FeMnCr/Cr3C2 coatings

Erosion Behavior of Cold-Sprayed Coatings Made of CoCrFeMnNi HEA and Tungsten Carbide Nanoparticles in a Nickel Matrix