Abstract:Thermal spray cermet based on tungsten carbide has been widely used due to its excellent wear resistance. The features of both carbide and binder phases are essential factors which determine the performance of cermet coating. The thermal cycling of WC–Co spray particles up to a temperature over the melting point of binder phase during thermal spraying involves the decarburization of carbide. The decarburization of carbide becomes severe with the decrease of carbide particle size, which makes it difficult yet to deposit a dense nanostructured WC–Co with a limited decarburization by thermal spraying. The decarburization not only reduces the wear-resistant phase but also leads to the formation of brittle Co–W–C ternary binder phase. Moreover, the limited decarburization involves the deposition of spray particle at a solid–liquid two-phase state with carbides at a solid state and metal binder in a molten state during spraying. High velocity impact of two-phase droplets as in high velocity oxy-fuel spraying (HVOF) results in the formation of a dense cermet coating and on the other hand leads to the possibility of rebounding of wear-resistant solid carbide particles. In this review article, the microstructural features of thermal spray WC–Co are examined based on the effect of the decarburization of tungsten carbide. The decarburization mechanisms of tungsten carbide are discussed for the control of decarburization of carbide. The effects of carbide particle size on the deposition process, adhesion of HVOF coating and wear performance of WC–Co coating as well are examined based on a solid–liquid two-phase deposition process. It is demonstrated that WC–Co cermet with different sizes of WC particles should be deposited by different processes. Moreover, the deposition of nanostructured WC–Co by thermal spraying and recent advances on the cold spraying of nanostructured WC–Co are introduced. The cold spraying with the proper design of spray powders will become promising process to deposit nanostructured WC–Co with pure cobalt binder with the hardness comparable to a sintered bulk and even high toughness of 18.9MPam1/2. The pure metastable metal binder phase evolved in the deposit makes it possible to deposit hard cermet through healing the non-bonded interfaces in the coating by post-spray annealing.

Characterization of Supersonic Plasma Sprayed WC-12Co Coatings

Microstructure and Corrosion Behaviour of WC-Co Coating Fabricated by Plasma Arc Welding

Study on Properties of Coatings Prepared by Supersonic Plasma Spraying with Three Kinds of WC-12Co Powder

Analysis of Microstructure of WC-12Co Coatings Prepared by the Three Kinds of Supersonic Thermal Spraying Processes

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Characterization of Nano-Structured WC-Co Deposited by Cold Spraying

Promising WC-30WB-10Co Cemented Carbide Coating with Improved Density and Hardness Deposited by High Velocity Oxy-Fuel Spraying: Microstructure and Mechanical Properties

Wear performance of the plasma sprayed fine WC-Co composite powders coatings

Properties of Supersonic Plasma Sprayed WC-17Co Nano-coating

Thermal sprayed WC-Co coatings and their mechanical properties

Comparison Between Wear Resistance of Subsonic Speed Flame Spraying Coating and Plasma Spraying Coating

Microstructure, Mechanical and Tribological Properties of WC-WCoB Coating

Effect of Cobalt and Chromium Content on Microstructure and Properties of WC-Co-Cr Coatings Prepared by High-Velocity Oxy-Fuel Spraying

Effect of Spraying Power on the Microstructure and Mechanical Properties of Supersonic Plasma-Sprayed Ni-based Alloy Coatings

Influence of Powder Porous Structure on the Deposition Behavior of Cold-Sprayed Wc-12co Coatings

Influence of Powder Structure on the Micro-Hardness and Fracture Toughness of Cold-Sprayed WC-12Co Deposit

Properties of WC-Co Ceramic Coatings of Ultra-Fine Grains Prepared by Electro-Thermal Explosion Method

Strengthening Mechanism and Properties of Co–WC Composite Coatings Deposited by Plasma‐transferred Arc Welding

Preparation and Characterization of WC/Co-W-C Cermet Coatings with Molten Zinc Corrosion Resistance by HVOF Spraying of Bimodal-Structured WC/Co Powder

Research on flame characteristics and coating growth process of titanium alloy in HVAF spraying

Relationships Between Feedstock Structure, Particle Parameter, Coating Deposition, Microstructure and Properties for Thermally Sprayed Conventional and Nanostructured WC–Co