Abstract:The effects of nanosized reinforcement particles on precipitation reactions in age-hardenable Al alloy matrix composites have been largely unknown. In this work, an Al-Zn-Mg-Cu matrix composite reinforced with uniformly distributed TiB2 nanoparticles was successfully produced. The solid-soluted, peak-aged and overaged materials were then characterized, at the atomic scale using (high-resolution) scanning transmission electron microscopy, to provide a fundamental insight into the interface precipitation. Our results demonstrated that the facetted TiB2 nanoparticles have a significant impact on the precipitation in matrix areas adjacent to the TiB2/Al interfaces. The interfaces after solid-solution treatment are tightly-bonded and oxide-free, and display two orientation relationships (ORs): the well-reported [21¯1¯0]TiB2//[101]Al, (0001)TiB2//(1¯11)Al (OR1) and the new [21¯1¯0]TiB2//[101]Al, (011¯0)TiB2//(111¯)Al (OR2). The interface precipitates (i.e. interphase) having the size of several tens of nanometers were formed after ageing and were determined to be (Zn1.5Cu0.5)Mg phase. Their formations were only related to the initial OR1 and OR2 where the mutual ORs between the TiB2, interphase and Al matrix were further developed. Periodically spaced misfit dislocations were revealed at the semi-coherent TiB2/Al interfaces, which are generally considered beneficial to the heterogeneous precipitation. They not only reduced nucleation energy barrier, but also acted as short-circuit diffusion paths for transporting solute atoms and vacancies, accelerating growth rate. However, the growth of interphase at the interface parallel to close-packed {111} Al planes was suppressed by the ultra-low accommodation factor. In addition, such an interface precipitation reduced the mismatch of the TiB2/Al interface, increasing the overall coherency and being potential for effective interface strengthening.

Microstructure and mechanical performances of ZTA/LaAl11O18 composite prepared by a heterogeneous precipitation method

Effects of Zr Addition on the Deformation Behavior, Microstructure and Mechanical Properties of Dental Ti Alloys

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

Microstructure and mechanical properties of Zn based composites reinforced by Ti3AlC2

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

Microstructures and mechanical properties of the in-situ formed nanocomposites of (ZrB2 + Al2O3) and AA7055 alloy

ZrO 2 Strengthened NiAl/Cr（Mo,Hf） Composite Fabricated by Powder Metallurgy

Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: Effects of SiC nanoparticles addition and heat treatment

Effect of Zr addition on the microstructure evolution and mechanical properties of extruded Al-Cu-Li-Mn alloys

Preparation and mechanical and tribological properties of A1(3)Zr+6082Al composites fabricated by magnetic stirring in situ

The effect of zirconium on the microstructure and mechanical properties of a super-high-strength Al-Zn-Mg-Cu alloy

Microstructure evolution and strengthening mechanisms of a high-performance TiN-reinforced Al-Mn-Mg-Sc-Zr alloy processed by laser powder bed fusion

Microstructures and Mechanical Properties of a L1 2 -structured precipitation Strengthened Co-based Superalloy

Effectively Inhibiting Abnormal Grain Growth of Alumina in ZTA with Low‐Content Fine‐Sized ZrO2 Inclusions Introduced by Infiltration and in Situ Precipitation

Atomic-scale investigation of the interface precipitation in a TiB2 nanoparticles reinforced Al–Zn–Mg–Cu matrix composite

Effects of ZrC content on the microstructure and mechanical property of ZrC/ZTA composites consolidated by hot pressing

Effect of combined addition of Zr, Ti and Y on microstructure and tensile properties of an Al-Zn-Mg-Cu alloy

Effect of alloying element Zr on microstructure and properties of Cu−Y2O3 composites

Preparation and Microstructures of CoAl(2)O(4) ZrO(2) Composite

ZrSiO4 toughed Al2O3 ceramics prepared by reaction sintering

Microstructure and Mechanical Properties of Al/Al4C3/Al2O3 Composite